Set of 3 waterproof roll-top Dry Pods keep gear organized and protected inside the Coyote Saddlebag's super-rugged, water resistant outer BombshellTM. Backed by a Limited Lifetime Warranty! 2 lower sacks; 1 middle sack; 30 liters total volume; 200-denier PTU coated Nylon; 1" Nylike webbing, heavy duty side release buckle; High visibility yellow; Designed specifically for Giant Loop saddlebags; Made in USA.
Coyote Saddlebag 2014 by Giant Loop
$342.00
NEW FOR 2014 - NOW 100% WATERPROOF! The choice for hardcore off-road expeditions. Carry gear for multi-day trips - and still work the entire saddle. Rides on rear fender and/or tail rack. Straps on to dirt bikes and dual sport motorcycles, no passenger pegs required. Includes set of 3 roll-top 100% waterproof fitted Dry Pod liners; Volume: 39 liters; Rear mounting system - use fender hooks or included webbing loop for easier, more flexible adjustment; Cinch ring with side-release buckled compression straps; Zipper defended by storm flap; Reflective accents for better visibility; 1 Hot Springs Heat Shield (new laser-cut aluminum) included; Military-spec materials and construction; Limited Lifetime Warranty; Made in U.S.A. Dimensions (fully packed): 61.5" - bottom of pannier, across top to bottom of other pannier bucket, 7" - height of bag in top center, 6" - distance from inside to outside of pannier bucket bottom, 9" - front to back in top center. COLORS: black, white, gray, yellow, orange.
Diablo Tank Bag 2013 by Giant Loop
$131.20
Minimalist tank bag solution for sport, dirt, adventure, dual-sport motorcycles. 4 liter capacity (main compartment) vs. 10 liter Fandango Tank Bag; Slim, trim profile; Tank Bag Dimensions: rear 6.5 tall, front 3.5 tall vs. Fandango rear 8 tall, front 5 tall; Easy on/off; Bag unzips from base layer to provide fuel fill access and for easy removal; Rubber and webbing carry handle; Clear vinyl map top pocket with Phifertex 11.7 oz vinyl polyester mesh bottom to control condensation; Removable inside divider to secure camera, cell phone, etc.; Lined with high-visibility yellow nylon; Water resistant Bomb ShellTM construction and material (22oz vinyl coated polyester trucker's tarp); Water resistant YKK zipper with storm flap; Beefy YKK coil zipper on Harness; Diamond-plate vinyl reinforcements; Sewn with military-grade thread to military quality specifications; Straps: 1-in. NylikeTM webbing with Delrin thumb-lock buckles concealed on harness under bag; Base Dimensions: 8.25 X 12 (same harness as Fandango); Additional harness available (not included) to move tank bag from bike-to-bike in seconds; Edges finished with polypropylene webbing; Includes seam sealing kit, detailed installation instructions and packing tip; Available in White, Gray, Yellow, Orange and original Black-on-Black Made in the U.S.A.
Fandango Tank Bag 2013 by Giant Loop
$131.20
NEW 2013: Limited Lifetime Warranty! Named for the rocky Oregon desert canyon and the lively Spanish dance, the Fandango Tank Bag straps on to a wide variety of motorcycles, including those with large-capacity dualsport fuel tanks (Clarke and Acerbis gas tanks without "tower" shaped fills), as well as many sport, sport touring and adventure touring motorcycles. Made from the the same tough, water resistant construction, "trucker's tarp" material and water resistant YKK zipper as our motorcycle saddlebags. And we've got colors to match white, gray, yellow, orange and original black-on-black. Seam grip sealer and brush included; 10 liter capacity (main copartment); Water resistant Bomb ShellTM construction and material (22oz vinyl coated polyester a.k.a., trucker's tarp); Bag unzips from base layer; Large harness cut out provides easy access to fuel fill; Rubber and webbing carry handle; Clear vinyl map top pocket; Divider inside (removable) to secure camera or electronics; Lined with high-visibility yellow nylon; Water resistant YKK zippers on bag; Beefy YKK coil zipper on harness; Diamond-plate vinyl reinforcements; Made in U.S.A.; Easy on/off; Slim, trim profile; Sewn with military-grade thread; Straps: 1-in. NylikeTM webbing with Delrin thumb-lock buckles; Base Dimensions: 8.25 X 12; Tank Bag Dimensions: rear 8 tall, front 5 tall; Includes detailed installation instructions and packing tips.
Fandango Tank Bag Pro by Giant Loop
$218.50
Protect tank and plastics with Giant Loop Vinyl Protective Film.For maximum off-road stability, add Giant Loop Pronghorn Straps. Protect tank and plastics with Giant Loop Vinyl Protective Film. Includes concealed document pocket. Electronics pass-through integrated throughout each compartment; Full length interior lining with Veltex hook-and-loop accepting fabric (compatible with many camera bag dividers); Movable divider with elastic tire pressure gauge holder and organizer slots; Exterior mesh pocket; Easy-access clear vinyl map pocket; D-ring harness mounts for new optional Pannier Pockets (2 liters each side); Volume: 8 liters; 22 oz vinyl coated polyester Bomb ShellTM reinforced with foam; Slip-Not and clear vinyl top; Rubber electronics port; Water resistant YKK zipper (bag); Beefy YKK coil zippers (harness); Nylike webbing; Reflective accents for visibility; Mil-spec materials and hardware; Limited Lifetime Warranty; Made in USA.
Great Basin Saddlebag 2014 by Giant Loop
$427.00
NEW FOR 2014 NOW 100% WATERPROOF! Set of 3 seam-sealed, roll top waterproof Dry Pods now included. Carry your gear where the passenger would sit on your bike the Adventure Proof Great Basin Saddlebag fits virtually any motorcycle designed to carry a passenger. Straps to passenger footrest mounts and rides on pillion seat. Backed by a Limited Lifetime Warranty! Volume: 60 liters; Super tough trucker's tarp Bomb ShellTM reinforced with ballistic nylon; "Beavertail" and floating compression straps more ways to carry the gear you need, the way you want it; Separate mounting and compression straps for easier gear access; Beefy, easy sliding YKK coil zipper protected by storm flap for water deflection; Cable lock pass-though to secure bag to bike while parked; Reflective accents for visibility; 1 Hot Springs Heat Shield (new laser-cut aluminum version) included; Military-spec materials and construction; Made in U.S.A.
Hot Spring Heat Shield by Giant Loop
$28.50
Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty. Highly recommended for the MoJavi Saddlebag, and as additional protection for dual exhaust motorcycles using all Giant Loop Pannier and Saddlebag systems. Rugged laser-cut aluminum construction; Stainless steel clamp included; Easy to install on virtually any motorcycle make or model; Dimensions: 6 long X 2.75 wide; Weight: 3.2 oz; Made in Bend, Oregon, U.S.A.
MoJaviTM Saddlebag 2013 by Giant Loop
$213.75
NEW! Volume: 13.5 liters (3 liters more 2 × 6 liter side pockets + 1.5 liter tool pocket); NEW! Top-access rear mounting system easier, more flexible adjustment (includes fender hooks and 30 of ballistic webbing for mounting on tail rack, passenger handles or double thickness plastics); NEW! Removable center tool pouch with 2 cam-buckle straps lash on additional gear, use tool pouch, or go naked; Dimensions: Center top pouch = 4 tall x 9 long x 5 wide; side pouches = 4 deep x 16 long x 7 wide; Straps on/off bike in seconds; Mounts without drilling or hardware required; Slim, trim profile rides like it's not even there; Bomb ShellTM: water resistant construction and rugged trucker tarp; Beefy, water resistant YKK zippers; Fits virtually every dirt bike, supermoto and dualsport motorcycle make and model; Only available in black; Made in the U.S.A.
Possibles Pouch by Giant Loop
$47.50
The universal Possibles PouchTM adds 2-liter easy access storage capacity to Giant Loop saddlebags and panniers and to any secure attachment point on virtually any motorcycle make or model. Includes 2 webbing and thumb-lock buckle straps. Named for the leather pouches carried by frontier explorers to keep critical gear, or "possibles," in one handy location. The Possibles Pouch is perfect for the many relatively small, lightweight motorcycling essentials: 21 front inner tube, snacks, beverages, gloves and tools. Upgrade to Giant Loop's Rubber Boa Straps to mount on dirt bike fenders, or Pronghorn Straps for maximum security and stability. Universal fit works on all motorcycles; 2 liters of easy access storage; Includes 2 webbing and thumb-lock buckle straps; Great storage for inner tubes, snacks, beverages, gloves, tools, etc.; Made in the U.S.A.
Pronghorn Straps by Giant Loop
$14.25
– $18.05
Every motorcyclist needs a handful of these multi-purpose, 26-inch-long, stretch polyurethane straps with unbreakable fasteners. You'll find a million uses for these quick, solid, tough straps. We've been using them for years to secure everything from luggage to water and fuel bottles to our Bushwackers Hand Guards. Sold in packages of 2, available in red with Giant Loop's iconic cow skull graphic and our design mantra: "Go Light. Go Fast. Go Far." Super tough stretch polyurethane; Multi-purpose straps; Unbreakable unfastener; Adjustable from 4 to 26; Quick, solid, and strong; Width 3/4; 2 per pack; Made in Canada; Red = 26 length; Orange = 20 length; Grey = 16 length.
Trailmaster
Adventure Crash Bar Bags for KTM 950 & 990 by Trailmaster Adventures
$119.00
Brilliant new concept in storage bags for your KTM 950/990 Adventure! Great location for storing tools, tubes, rain gear, spare parts, and seldom used items. Durable 1000 Denier Cordura Exterior; 1000 Denier Cordura Trim; 420 Denier Coated Pacnyl Lining; Flame Resistant Silver Reflective Tape, Certified to NFPA.; ANSI Industrial Grade Velcro strapping; Heavy Duty #8 YKK zippers; Easy access; Color: black w/gray reflective trim; Capacity: KTM = 3.3ltr.; Hepco Becker/SW Motech = 3.7ltr; Touratech = 3.9ltr; Low center of gravity location; Inner liner is light in color to make it easy to see inside!; 2 bags included in set, one for each side; Made in the U.S.A.
Crash Bar Bags for KTM 1190 Adventure by Trailmaster Adventures
$142.00
The new KTM 1190R Crash Bar bags are here. They attach to the o.e.m. KTM 1190R crash protection bars and fit the KTM Powerparts crash bars for the 1190 standard model. These storage bags are for all those items you need, but don't have a good place to put them. Tire irons, extra gloves, extra tubes, tube changing items, rain gear, bike cover and any other lightweight item you can think of. The inner liner is light in color to make it easy to see what you have in the bag. Durable 1000 Denier Cordura Exterior; Durable 1000 Denier Cordura Exterior; 1000 Denier Cordura Trim; 420 Denier Coated Pacnyl Lining; Flame Resistant Silver Reflective Tape, Certified to NFPA.; ANSI Industrial Grade Velcro strapping; Heavy Duty #8 YKK zippers; Easy access; Color: black w/gray reflective trim; Capacity: KTM = 3.9 liters each bag; Low center of gravity location; Inner liner is light in color to make it easy to see inside!; Sold & priced per pair; Made in the U.S.A.
USWE
Grid Pro Bottle by USWE
$19.99
The Grid ProTM bottle lets you enjoy cool hydration just like the pro's. Gives you quick access through the extended drinking tube without the need to take off your helmet when you're in the pit or paddock. The aluminum bottle keeps liquids cooler and gives you a high-profile racing bottle. Made for racers; Reusable & BPA-free; Aluminum: Taste-free and durable; 1x Aluminum bottle with plastic cap; Silicone drink tube & bite valve; .7 Liter; Color - red.
H1 Handsfree Hydration Pack by USWE
$71.95
The H1 HANDSFREETM system is made for racers who want the lightest hydration pack on the market. It's small, discrete, lightweight, and thanks to the hands free accessories kit ensures all you have to do is stay focused on the track ahead. With the slim fitting, body hugging harness design it can be worn underneath a chest protector or racing suite (outside back protector). Delivering super-fast, hands free, access to hydration inside your helmet, it ensures you'll stay hydrated and focused. 0,5L / 18oz liquid capacity;; Adult size, one size (S-XL) Weight = 235g; Color = Black/Red; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube & silicone bite valve; Helmet HandsfreeTM kit; Designed in Sweden.
H2 NDM Hydration Pack 2.5L by USWE
$62.95
The H2 NDMTM hydration pack has been produced for hardcore off-road racing and is the preferred choice of many of USWE's top Enduro World Championship performers. No matter what the terrain, the highly effective harness design prevents the 2.5 litre hydration system moving on your back, ensuring an absolute, top-class, fit. The harness features a smart Velcro and stretch strap function which allows full body movement and secure fitment for any size of rider. In addition, the H2 NDMTM contains one luggage pocket for storage of personal belongings like phone, keys, medicine, energy bar, etc. Multi pocket for keys, wallet, phone; Designed for high-end competitive use; Easy open-close adaptor cap, silicone drink tube, 90 degree bite valve; Adult size, one size (S-XL); 2.5L / 85oz liquid capacity; Weight: 410g; Color - black/red; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube; 90 degree bite valve; Designed in Sweden.
H3 NDM Hydration Pack 1.2L by USWE
$81.95
Superlight hydration harness made for fast and demanding terrain. Prevents any bouncing with its revolutionary 4-point harness concept, which provides a truly customized fit. Media pocket and a removable multi-pocket . The multi-pocket can easily be detached to make the pack even lighter and slimmer; Carries multi-tool, mini-pump, spare tube, MP3, phone, wallet, keys etc.; 1,2L / 41oz liquid capacity; Adult size, one size (S-XL); Weight = 340g; Color - Black/White; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube; 90 degree bite valve; Designed in Sweden.
H4 NDM Hydration Pack 2.5L by USWE
$89.95
The H4 NDMTM is the big daddy of the USWE hydration pack range. Offering everything a hardy adventurer requires serious storage space and a 2.5litre/ 85oz hydration bladder it delivers class-leading fitment with its ergonomic strap design. In addition to one cavernous main storeroom compartment, the H4 NDMTM also features numerous extra pockets ideal for tools and spares, energy bars, and phone/wallet/keys. Media pocket, tool organizer pocket; Multi-tool, pump, spare tube, extra layers, MP3, phone, wallet, keys etc.; 2,5L (85oz) liquid capacity; Adult size, one size (S-XL); 9,5L total capacity; Weight= 520g; Color Black/White; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube; 90 degree bite valve; Designed in Sweden.
Helmet Handsfree Kit by USWE
$30.95
USWE's Helmet HandsfreeTM system allows the rider quick access to hydration inside the helmet. It's 100% hands free, making it easier and safer to hydrate while riding. Hands free hydration enables the ability to drink more frequently and therefore stay hydrated and focused. Compatible with helmets with removable/washable race fit inner liner. Silicone drink tube and bite valve; Quick seal coupling; Velcro straps.
Quick Refill Bottle by USWE
$19.95
The USWE Quick Refill BottleTM makes for quick and easy refills of the hydration system during pit stops. Just connect the bottle to the hydration system, release the air valve and the system will quickly refill. Fast and easy. The Quick Refill BottleTM is made of material that's BPA-free and approved for food-stuffs. One size; Color black; Fast and easy; Aluminum bottle with plastic cap; Silicone drink tube & bite valve.
SP1 Handsfree Hydration Pack by USWE
$71.95
The superlight SP1 HANDSFREETM hydration pack is designed to be attached directly to the rear of the neck brace and is perfect for short, sharp intense racing. This unique pack provides a well balanced fit on the brace and is easily attached and detached without any tools. Helmet HandsfreeTM kit is included, which makes it possible to drink 100% hands free inside the helmet. Compatible with Leatt Brace, EVS Evolution, Moveo neck braces; One size; .5L (18oz.); Weight = 113g; Color = Black/Red; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube & silicone bite valve; Helmet HandsfreeTM kit; Designed in Sweden.
SP2 Handsfree Hydration Pack by USWE
$71.95
The superlight SP2 HANDSFREETM hydration pack is designed to be attached directly to the rear of the neck brace and is perfect for short, sharp intense racing. This unique pack provides a well balanced fit on the brace and is easily attached and detached without any tools. Helmet HandsfreeTM kit is included, which makes it possible to drink 100% hands free inside the helmet. Compatible with Alpinestars neck braces; One size; .5L (18oz.); Weight = 113g; Color = Black/Red; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube & silicone bite valve; Helmet HandsfreeTM kit; Designed in Sweden.
SP3 Handsfree Hydration Pack by USWE
$71.95
The superlight SP3 HANDSFREETM hydration pack is designed to be attached directly to the rear of the neck brace and is perfect for short, sharp intense racing. This unique pack provides a well balanced fit on the brace and is easily attached and detached without any tools. Helmet HandsfreeTM kit is included, which makes it possible to drink 100% hands free inside the helmet. Compatible with Atlas & Ortema neck braces; One size; .5L (18oz.); Weight = 113g; Color = Black/Red; 1x Disposable hydration bladder; Easy open/close adaptor cap; Silicone drink tube & silicone bite valve; Helmet HandsfreeTM kit; Designed in Sweden.
Wolfman
Blackhawk Tank Bag by Wolfman
$116.99
The Blackhawk Tank Bag fits our line between the compact Enduro Tank Bag and the Explorer Lite. 8-liter capacity and trim lines give it great clearance for off-road riding. The Curved base contours snugly to most sloped tanks. The foam structure gives the Blackhawk "soft-rigidity", allowing the bag to flex. The new Map/Clear Pocket is a step forward in versatility. We have taken the traditional "Map Pocket" and made it more useful to riders who use electronics; we have incorporated a strip of "Loop" material inside the pocket, and include a strip of Adhesive "Hook" to attach to your smart phone, GPS, Spot, etc. so they stay put. Items can be kept organized with one stealthy outside pocket and an internal mesh pocket under the top. The silver interior makes it easy to see the contents of the bag. A small removable/adjustable bunji-cord across the top provides a convenient spot for gloves and such while fueling. (Please don't ride with your gloves under the shock-cord or you may never see them again.) The Blackhawk mounts securely to the tank via our 4-point harness. The bag also incorporates fore and aft flexibility allowing the user to get the perfect bag placement on the tank. The Blackhawk utilizes the same 4-point harness as used on the Explorer Lite, Rainier, and Large Expedition Tank bags, making switching out bags a snap.
E-12 Saddlebags by Wolfman
$149.39
Rack-less saddle bags that combine generous capacity with versatility and an out-of-the-way fit. The E-12 Saddle Bags strike a balance between carrying capacity, rider mobility and convenience. Ideal for enduro touring, they hold a surprisingly generous load without the need for a rack. The highly adjustable mounts are able to fit virtually all enduro/dual sport motorcycles and the compact design does not hinder the rider. The E-12s are a refinement and improvement of our already successful E-10 Saddle Bags. The new E-12s are more versatile and the updated design and construction make for even stronger and more robust bags. Redesigned for more internal capacity; Two 2 straps across the seat; 8 -2 D Rings on the bags for more tie down options; "V" Compression strap on each bag to keep the contents stable; Quick and easy on-off. No rack system needed; 8 D-rings on the top to attach the Enduro Duffel, Rolie Bags and our Renegade Duffel; Full highly coated 1680 denier ballistic fabric construction along with foam and non-scratch on the bike side; Heavy Duty #10 YKK coil zipper main opening; Reflective webbing accents for nighttime visibility; Made in the U.S.A.
Enduro Fender Bag by Wolfman
$25.19
The Enduro Fender Bag was designed to carry spare tubes on the front fender. 1 webbing, steel gutter hooks and ballistic nylon construction make a stable, durable bag that stays put. Note: Many front fenders are only durable enough to carry the weight of a tube or two, not heavy items. Also, the Enduro Fender Bag is NOT recommended for the 2008-to-present Kawasaki KLR 650 as the bag will not sit securely on the front fender. Keep spare tubes snug and out of the way so they'll be ready when needed. Ballistics nylon construction; Non-scratch, non-skid bottom; 1" Heavy Duty metal hooks for multiple mounting options; Universal straps; Made in the U.S.A.
Enduro Tank Bag by Wolfman
$85.49
Finally a tank bag for dual sport and dirt bikes. The Enduro Tank Bag will fit virtually all dual sport and dirt bikes, from the Suzuki DR650,DRZ400, to the XR 650L and the KTM525E/XC, and most bikes in between. New: 4-point quick release mounting and no-skid, no-scratch pad keeps the Enduro Tank Bag in place during the most aggressive riding. The innovative design allows the bag to sit on the tank and not interfere with the gas cap or the vent hose. For 2012: the mounting harness is now the same for the Enduro Tank Bag, the Enduro Pocket and the Small Expedition Tank Bag. Easily swap between the bags as your needs change without changing the harness. Laminated foam sides, bottom, and rear; Non-scratch, non-skid bottom; Reflective webbing on sides; NEW! 4 point quick-release universal mounting system. Fits most Enduro and Dual Sports bikes; Inside mesh pocket; Outside mesh pocket; Removable map pocket; Key Clip; Made in the U.S.A.
Enduro Tool Bag by Wolfman
$49.94
Compact and stable rear fender bag keeps tools handy. This 2-liter bag mounts on the rear fender with a bolt-on plastic plate that stabilizes the bag with hook-and-loop fabric. Compression straps and sturdy construction further add stability. The bag itself is easily removed so you can carry your tools right to the job. Includes mounting base designed to be hard-mounted, bolted, to the rear fender. Mounting hardware included. Use the base as a drilling template. Compression straps and Duraflex buckles; Removable from base and portable; External zipper dust cover; Extra heavy duty zipper; Spacious 3.5 liter compartment; Includes mounting base with Velcro bag attachment; Made in the U.S.A.
Expedition Dry Duffel by Wolfman
$104.84
– $125.09
Four compression straps and two mounting straps keep things tight on the bike. The dual carrying handle and removable shoulder strap make off-bike transport easy. All Expedition Dry-Line bags are made in the USA and feature heavy-duty vinyl construction with fully sealed radio-frequency welded seams. Roll-top closures with no-wick webbing seal out water, mud, and dust. We recommend a three roll minimum for maximum weatherproofing. 100% Waterproof radio frequency welded seams; Ultra tough 22oz vinyl body and 34oz vinyl sides; Choice of colors: black/yellow or all black. Simple effective roll-top design; 4 compression straps, two over the body, one at each end; Deluxe carry handle; Removable shoulder strap and two mounting straps included; Repairable with the vinyl repair kit; Made in the U.S.A.
Expedition Dry Saddlebags by Wolfman
$234.00
The bags have a pair of over-the-top straps between them, then each bag is mounted to the rack via four-points and two compression straps. An additional top compression strap and and internal stiffeners help further stabilize the load. A replaceable rubber pad protects the bag against rack abrasions and prevents excessive bag movement. No loose moving bags here! During testing we saw that once the bags were attached to the racks, they were attached so securely that we could have dragged the bike by the bags. Yet when the bags need to come off, they do so quickly with the innovative release system. 100% Waterproof fabric 22oz body and 34oz bottom; Radio Frequency welded seams; Waterproof roll-top with no-wick webbing; Multi-compression straps to cinch the load tight; Recycled tire rubber backing pad; Extra tall opening for size adjustability; Internal Butterfly stiffener helps keep contents compressed evenly, protects the insides of the bags from abrasion and sharp objects, and it is removable and replaceable; Vinyl tears are repairable with the Vinyl Repair Kit; Completely replaceable mounting harnesses. Cut a strap too short? Change bikes? Wear, tear, or damage? No worries! Replacement strap kits are available. Made in the U.S.A.
Explorer Lite Tank Bag by Wolfman
$129.59
Great fitting mid-sized tank bag for most sloped fuel tanks. The Explorer Lite Tank Bag was designed in response to riders wanting something "smaller" than our Rainier Tank Bag. It is 2 shorter than the Rainier and has a slimmer width for more handlebar clearance. The curved bottom makes for an excellent fit on most sloped tanks and it excels on Dual Sport and Adventure bikes. On the KTM 950/990 Adventure it nestles between the two gas caps so you do not have to remove the bag to get gas. And expandable gusset adds capacity when you need it. An optional Top Pocket (sold separately) can add even more. Reflective accents add nighttime visibility and a carry handle makes it easy to take it with you when you un-clip it. All foam and ballistic nylon construction; Expandable gusset; Zippered front pocket; Interior zippered mesh pocket and key clip; 4 point mounting system; Non-slip, non-scratch bottom; Reflective side accents and carry handle; Made in the U.S.A.
Large Rolie Bags by Wolfman
$70.19
Wolfman Rolie Bags offer superior protection against the elements and allow you to personalize your kit and carry the gear you need the way you like to carry it. Using different mounting options, the Rolie Bag you use as a tail bag today can be mounted on your tank tomorrow or used as one of a pair of saddle bags. Same bag with multi-function. Waterproof, Versatile same bag, many uses with available strap and harness options, Basic Mounting Straps are included with the bag.
Medium Rolie Bag by Wolfman
$54.89
Wolfman Rolie Bags offer superior protection against the elements and allow you to personalize your kit and carry the gear you need the way you like to carry it. Using different mounting options, the Rolie Bag you use as a tail bag today can be mounted on your tank tomorrow or used as one of a pair of saddle bags. Same bag with multi-function. Waterproof, Superior Construction, Versatile same bag, many uses with available strap and harness options, Basic Mounting Straps are included with the bag.
Bearings
Connecting Rod Kits for KTM, Husaberg by Hot Rods
$79.95
– $139.95
The KTM, Husaberg & Husqvarna connecting rod kits by Hot Rod are an affordable way to repair your crankshaft instead of throwing them away. Premium quality; Inexpensive; Everything is included to rebuild your crankshaft; Connecting rod, big-end bearing, thrust washers, crank pin, & piston pin bearing (2 strokes only); 8620 AISI forged steel rod for maximum strength; 8620 AISI carburised crank pin for durability; Phosphor bronze thrust washers; Silver coated big-end bearing for for reduced friction and temperatures.
Linkage Bearing Rebuild kit for KTM, Husqvarna 125-450
$84.95
Contains all of the bearings, seals, bearing sleeves needed to rebuild the swingarm linkage to factory specs; Most complete kit in the industry; Fits: '11- '14 125-450 SX, SXF & '12-'14 250,300,350 XC, XCF & '14 Husqvarna.
Lower Shock Heim Joint Bearing Kit for KTM, Husaberg
$29.95
This kit includes a long lasting, high quality heim joint, 2 seals, and 2 spacer inserts. It fits in the swingarm where the shock attaches. heim joint; 2 seals; 2 spacers.
Main Bearings & Seals Kit for KTM, Husaberg, Husqvarna by Hot Rods
$46.95
– $96.95
Precision, high-quality main bearing and seal kits complement Hot Rods crankshaft assemblies; All kits contain two main bearings and two seals.
Piston Pin Bearing for KTM, Husaberg, Husqvarna 50cc - 300cc
$15.95
– $16.95
High quality precision machined replacement needle bearings; Will work with Vertex (OEM), Wiseco, ProX and Wossner pistons.
Rear Wheel Spacers for KTM, Husaberg, Husqvarna
$19.95
Designed for years of service even in the dirtiest riding environments; Aluminum spacers feature a hardened steel shell pressed over the aluminum to provide superior wear surface; Manufactured with 52100 bearing steel that is through hardened, precision ground and plated for years of service; Easy installation.
Steering Head Bearing Kits for KTM, Husaberg & Husqvarna
Swingarm Bearing Rebuild Kit for KTM, Husaberg, Husqvarna
$49.95
– $69.95
Contains all of the bearings, seals, bearing sleeves, and spacers required to rebuild a swing arm to factory specifications; Manufactured from 52100 bearing steel for improved performance and extended life; Features Teflon D coated seals for superior performance.
Unshock Shock & Fork Thrust Bearing Kits for WP/Ohlins/KTM/Husaberg, Husqvarna
$27.49
– $44.95
The Unshock Thrust Bearing Kits are just the ticket to improve your shock and fork action. Designed to reduce binding in the spring as it compresses. The Unshock Thrust Bearing Kits are a long overlooked inexpensive and easy to install improvement to your WP/Ohlins/KTM/Husaberg front and rear suspension. Eases pre-load adjustment; Prevents spring binding during compression and rebound; Sealed to prevent contamination; Provides consistent spring action; Includes two thrust washers, two o-rings, and one thrust bearing (shock kit only); Improves shock/fork action; Easy to install.
Upper Shock Bearing/Heim Bearing for KTM, Husaberg, Husqvarna
$24.95
Contains the upper heim bearing, seals, and spacers needed to replace the upper heim bearing.
Body
Fender adapter
2013 SX/XC Front Fender Adaptor Kit for KTM by Flatland
$44.95
The Front Fender Adaptor Kit enables you to replace the stock flimsy front fender with the new, updated, stronger 2013 SX/XC front fender. The SX/XC fender is extremely stable in muddy conditions and accommodates a fender bag. Enables mounting 2013 SX/XC front fender; Durable aluminum construction; Lightweight; Easy to install in minutes; Excellent for muddy conditions; Accommodates a fender bag; Does NOT include fender; Made in the U.S.A.
High Mount Front Fender Kit for KTM 1190
$59.95
– $89.90
The o.e.m. low front fender can be problematic and dangerous on dirt/gravel roads and during off-road excursions, especially when the conditions become wet and muddy. It can clog with mud or rocks, lock-up the front wheel and throw you on your head. The KTM 1190 High Mount Front Fender Kit enables you to remove the o.e.m. low front fender and replace it with the '08-'12 SX/XC front fender or a Super Moto style front fender. Enables mounting '08 '12 SX/XC or SM front fender; Durable aluminum construction; CNC machined for precise fit; Includes horn relocation bracket; Lightweight; Quick & easy to install; Allows clearance for muddy conditions and knobby tires; Fits KTM '13 '14 KTM 1190 Adventure & R models; ALL mounting hardware included; Available with or without front fender; Made in the U.S.A.
License Plate Holder by EE
$14.95
This holder is made of tough plastic and comes with all the necessary hardware for mounting. Fits almost any off-road rear fender.
Fuel tanks & jugs
Fuel jug accessories by Tough Jug
$2.95
– $28.95
Replacement and upgrade parts for all Tough Jug fuel containers. Replacement o-ring; Replacement spout; Small tank adapter; KTM rubber adapter.
Fuel Jug w/Red Ripper Cap by Tuff Jug
$37.95
– $49.95
Pours 5 gallons in 45 seconds; Fluids stop flowing after reaching the end of the spout automatically; Just pull up and the valve shuts off fluid flow; Self-venting, no vent to open and close or to leak when pouring; Stops over filling and prevents spilling; Easy to use, no spilling, no mess; Not legal in California; Available in orange, red, white, blue; 2 sizes, 5 gallon (20 liter) or 2.5 gallon (10 liter); Non-skid bottom.
Large Capacity Fuel Tanks for KTM, Husaberg by IMS
$259.00
Great fit and finish; Gas cap included; Necessary hardware included; Must re-use stock petcock; Available in natural or black; Made in the U.S.A.
Plastic
Air Box Covers for KTM by Acerbis
$39.95
Acerbis was established in 1973 by Franco Acerbis. The foundation of the company was developed from the challenges Franco experienced in his own race career in the early 70s. The first product Franco created was the NOST front fender, as he found that stock fenders were too short and were not effective in keeping mud from splattering and blocking his and other racers' vision during competition. Today Acerbis continues to produce innovative and protective aftermarket accessories with the same enthusiasm and passion as our founder had in the early years. Over 30 years of experience with the best off-road racers in the world has enriched our constant technical development, allowing us to become a premier company within the motorcycle industry. OEM color-matched for direct replacement. Pre-drilled and mount to stock locations.
Euro Style Pro-Pack 145 Piece Kit for KTM, Husaberg, Husqvarna by Bolt
$56.95
Only aftermarket company to offer hardware in KTM, Husaberg, '14 Husqvarna factory style and finish. Includes over 145 pieces of M6 and M8 dimpled flange bolts, concave washers, carb screws, shroud screws, sprocket bolts, Brembo style brake pin clips, and more. Includes 3 sizes of factory style aluminum bushings, aluminum rim-lock spacers, drain plug washers, sub-frame bolts, M5 dimpled flange bolts and valve stem grommets. Fits all full size late model KTM, Husaberg, '14 Husqvarna off road motorcycles.
Fork Covers for KTM, Husaberg, Husqvarna by Acerbis
$31.95
Acerbis was established in 1973 by Franco Acerbis. The foundation of the company was developed from the challenges Franco experienced in his own race career in the early 70s. The first product Franco created was the NOST front fender, as he found that stock fenders were too short and were not effective in keeping mud from splattering and blocking his and other racers' vision during competition. Today Acerbis continues to produce innovative and protective aftermarket accessories with the same enthusiasm and passion as our founder had in the early years. Over 30 years of experience with the best off-road racers in the world has enriched our constant technical development, allowing us to become a premier company within the motorcycle industry. Original factory shape of the O.E.M. plastic; O.E.M. color-matched for direct replacement; Pre-drilled and mount to stock locations; Sold as a pair.
Front Brake Cover Mounting Bracket for KTM, Husaberg, Husqvarna by Acerbis
$26.95
Machine specific mount kit for X-Brake & Spider Evolution Front Disc Covers; Machined aluminum flange; Allows removing wheel without removing disc cover; Fits up to 270mm discs; Disc cover are sold separately; Only works with stock hubs; Fits: '04-'14 KTM 125-525 & '04-'14 Husaberg 125-570 & '14 Husqvarna 125-501.
Front Fender for KTM, Husaberg by Acerbis
$22.99
– $23.95
Acerbis was established in 1973 by Franco Acerbis. The foundation of the company was developed from the challenges Franco experienced in his own race career in the early 70s. The first product Franco created was the NOST front fender, as he found that stock fenders were too short and were not effective in keeping mud from splattering and blocking his and other racers' vision during competition. Today Acerbis continues to produce innovative and protective aftermarket accessories with the same enthusiasm and passion as our founder had in the early years. Over 30 years of experience with the best off-road racers in the world has enriched our constant technical development, allowing us to become a premier company within the motorcycle industry. Original factory shape of the O.E.M. plastic; O.E.M. color-matched for direct replacement; Pre-drilled and mount to stock locations.
Front Number Plates for KTM by Acerbis
$23.99
Acerbis was established in 1973 by Franco Acerbis. The foundation of the company was developed from the challenges Franco experienced in his own race career in the early 70s. The first product Franco created was the NOST front fender, as he found that stock fenders were too short and were not effective in keeping mud from splattering and blocking his and other racers' vision during competition. Today Acerbis continues to produce innovative and protective aftermarket accessories with the same enthusiasm and passion as our founder had in the early years. Over 30 years of experience with the best off-road racers in the world has enriched our constant technical development, allowing us to become a premier company within the motorcycle industry. Original factory shape of the OEM plastic. OEM color-matched for direct replacement. Pre-drilled and mount to stock locations.
Fuel Tank Petcock for KTM, Husaberg, Husqvarna
$29.69
Fits KTM, Husaberg, '14 Husqvarna, IMS, Acerbis, Clark, Clockworks; Features on, off, and reserve.
Full Plastic Fastener Kit for KTM by Bolt
$19.95
Includes all factory replica fasteners and aluminum bushings needed to fasten complete bodywork; OEM quality fasteners at a fraction of the cost; A must when installing new plastic on your bike.
High Mount Front Fender Kit for KTM 1190
$59.95
– $89.90
The o.e.m. low front fender can be problematic and dangerous on dirt/gravel roads and during off-road excursions, especially when the conditions become wet and muddy. It can clog with mud or rocks, lock-up the front wheel and throw you on your head. The KTM 1190 High Mount Front Fender Kit enables you to remove the o.e.m. low front fender and replace it with the '08-'12 SX/XC front fender or a Super Moto style front fender. Enables mounting '08 '12 SX/XC or SM front fender; Durable aluminum construction; CNC machined for precise fit; Includes horn relocation bracket; Lightweight; Quick & easy to install; Allows clearance for muddy conditions and knobby tires; Fits KTM '13 '14 KTM 1190 Adventure & R models; ALL mounting hardware included; Available with or without front fender; Made in the U.S.A.
Large Capacity Fuel Tanks for KTM, Husaberg by IMS
$259.00
Great fit and finish; Gas cap included; Necessary hardware included; Must re-use stock petcock; Available in natural or black; Made in the U.S.A.
Brakes
Brake Fluid
RBF 600 Racing Factory Line Brake Fluid by Motul
$21.95
For all types of hydraulic brake and clutch actuators requiring non-silicone synthetic fluid. Specially designed to resist the extreme temperatures generated by carbon and ceramic racing brakes with minimum brake cooling. 100% Synthetic Racing Fluid DOT 4; Very high boiling point: 594°F / 312°C; Widely exceeds DOT 3, DOT 4 and DOT 5.1 standards; Ultra efficient in the rain: Very high wet boiling point 421°F / 216°C.
RBF660 Pro Racing Brake Fluid by Motul
$29.95
For all types of hydraulic brake and clutch actuators requiring non-silicone synthetic fluid. Specially designed to resist the extreme temperatures generated by carbon and ceramic racing brakes with minimum brake cooling. 100% Synthetic Racing Fluid DOT 4; Very high boiling point: 617°F / 325°C; Widely exceeds DOT 3, DOT 4 and DOT 5.1 standards; Ultra efficient in the rain: Very high wet boiling point 400°F / 204°C.
Coolers
Brake Caliper Cooler KTM, Husaberg, Husqvarna
$49.95
The KTM, Husaberg, Husqvarna Rear Caliper Cooler STOPS brake fade caused by extreme fluid temperatures. No more brake failure during those tight woods sections or long down hills. QUICK in line installation with the supplied chrome-moly banjo bolt & seal washers. Brake fluid cycles in and out of the brake cooler with each push of the brake pedal. With this action the cooler dissipates heat from the brake fluid.
Brake Reservoir Master Cylinder Cooler for KTM, Husaberg, Husqvarna
$31.95
The KTM, Husaberg, Husqvarna rear brake reservoir cooler, made by System Tech Racing, increases the fluid capacity keeping the system from running dry on long distance or muddy events where the brake pads undergo extreme wear causing a major drop in fluid level. It also reduces the fluid temperature to increase reliability. Increases fluid capacity; Reduces fluid temperature; Quick & easy installation; Bling factor; Made in the U.S.A.
Mule Cool Rear Brake Caliper Cooler for KTM 640, 690, 950, 990, 1190 by Slavens
$59.95
The KTM 950, 990 Mule Cool Rear Brake Caliper Cooler greatly reduces brake fade caused by extreme fluid temperatures. No more brake failure during those long down hill sections or when riding 2 up. Quick in-line installation with the supplied stainless steel banjo bolt & seal washers. Brake fluid cycles in and out of the brake cooler with each push of the brake pedal. With this action the cooler dissipates heat from the brake fluid ensuring positive brake control at all times. Greatly reduces brake fade (when used with fresh Motul RBF600 or 660); Extends fluid service life; Quick and easy installation (under 5 minutes); Positive brake control at all times; Made in the U.S.A.
Disc Guards
Brake Disc Guard Front for KTM, Husaberg, Husqvarna
$84.95
Stop ride ending damage to your front disc rotor with this ultra tough KTM, Husaberg, Husqvarna front disc guard. Machined from durable aluminum billet. All mounting hardware is included. Stops ride ending damage; Lightweight & durable aluminum; CNC machined billet aluminum for perfect fit; Includes all mounting hardware.
Brake Disc Guard Rear for KTM, Husaberg, Husqvarna by Bullet Proof
$114.50
– $119.95
This is the toughest rear disc guard, shark fin on the planet. If you can destroy it, we will replace it for FREE. Lifetime guarantee; Tough machined billet aluminum design; Secure axle mounting system; Available in polished, black, blue, & orange; Bling factor; Made in the U.S.A.
Brake Disc Guard Rear for KTM, Husaberg, Husqvarna by Enduro Engineering
$89.95
No more ride ending damaged disc brake rotors. This trick looking Enduro Engineering billet machined rear disc guard will protect your KTM, Husaberg disc rotor from the worst possible trail trash. CNC machined from durable billet aluminum alloy; Deflects potentially damaging rocks and debris; Replaces entire brake caliper carrier; Secured by the axle mounting system; Extremely durable; Replaceable fin; Made in the U.S.A.
Brake Disc Guard Rear for Sherco by Bullet Proof
$117.00
– $122.00
This is the toughest rear disc guard, shark fin on the planet. If you can destroy it, we will replace it for FREE. Lifetime guarantee; Tough machined billet aluminum design; Secure axle mounting system; Available in polished, black, blue, & orange; Bling factor; Made in the U.S.A.
Front Brake Cover Mounting Bracket for KTM, Husaberg, Husqvarna by Acerbis
$26.95
Machine specific mount kit for X-Brake & Spider Evolution Front Disc Covers; Machined aluminum flange; Allows removing wheel without removing disc cover; Fits up to 270mm discs; Disc cover are sold separately; Only works with stock hubs.
Front Disc Guard for KTM, Husaberg, Husqvarna by Bullet Proof
$105.00
– $110.00
This is the toughest front disc guard on the planet. Machined from a 2 solid block of billet aluminum. If you can destroy it, we will replace it for FREE. Typical of all Bullet Proof Designs products, this is the absolute best front disc guard available anywhere, period! Lifetime guarantee; Tough machined billet aluminum design; Secure 2 point axle/caliper bolt mounting system; Available in polished, black, blue, & orange; Bling factor; Made in the U.S.A.
Front Disc Guard for KTM, Husaberg, Husqvarna by STR
$149.95
– $184.95
The STR Front Disc Guard is much more than a motocross style deflector. It's a very strong, durable, robust component design. The disc guard is made from carbon fiber or G10 composite, the perimeter is wrapped with UHMW (ultra high molecular weight) composite material and that is mounted to a CNC machined billet aluminum carrier with high quality hardware. Available in carbon fiber or G10 composite material; Lightweight Carbon fiber = 8 oz. & G10 = 10; Durable carbon = 2.5mm thick, G10 = 3mm thick; CNC machined 6061 billet aluminum carrier; Replaceable UHMW perimeter scrub guards; CNC mount is available in orange, blue, or polished.
Front Disc Guard for Sherco by Bullet Proof
$107.00
– $112.00
This is the toughest front disc guard on the planet. Machined from a 2 solid block of billet aluminum. If you can destroy it, we will replace it for FREE. Typical of all Bullet Proof Designs products, this is the absolute best front disc guard available anywhere, period! Lifetime guarantee; Tough machined billet aluminum design; Secure 2 point axle/caliper bolt mounting system; Available in polished & blue; Bling factor; Made in the U.S.A.
X-Brake Front Disc Cover for KTM, Husaberg, Husqvarna by Acerbis
$26.95
Unique design allows you to change the tire or brake pads without removing the disc cover; Keep sticks, rocks, and debris from damaging or becoming tangled in the front rotor; Weight savings up to 35% over traditional covers; Excellent venting to keep the brake cool in all conditions; Extended coverage protects the brake caliper; Covers are constructed of polypropylene; Machined-aluminum flanged insert; Suitable for brake discs up to 275mm dia.; Carbon fiber look; Easy to install.
LH Rear Brake Kit
Dual Actuated Left Hand Rear Brake Kit for Honda, Yamaha by Rekluse
$289.00
The Rekluse Dual Actuated Left Hand Rear Brake Kit enhances rider control and enables the rider to use the left hand lever or right side rear brake pedal to actuate the rear brake. Adding additional rear brake control to the left hand (the brake pedal and the clutch lever remain fully functional) enhances your riding experience by significantly improving braking control in tight corners, right turns, and other technical riding situations such as switchbacks or rocky hill climbs. O.E.M. clutch master cylinder and clutch lever remain intact and fully functional; The LH brake kits mounts next to the clutch master cylinder and works in conjunction with it; Maintains full use of the clutch/clutch lever while adding a LH rear brake lever; Excellent rear brake modulation with a light lever pull; Amazing in switchback conditions; Dual-actuated system that enables brake activation with either the left hand lever or right foot pedal; Increases rider confidence; Reduces crashes; Includes master cylinder with lever, hydraulic line, and slave cylinder insert; Retains the use of the rear brake pedal; Easy to install; High quality components; Made in the U.S.A.
Dual Actuated Left Hand Rear Brake Kit for KTM, Husaberg, Husqvarna by Rekluse
$289.00
The Rekluse Dual Actuated Left Hand Rear Brake Kit enhances rider control and enables the rider to use the left hand lever or right side rear brake pedal to actuate the rear brake. Adding additional rear brake control to the left hand (the brake pedal and the clutch lever remain fully functional) enhances your riding experience by significantly improving braking control in tight corners, right turns, and other technical riding situations such as switchbacks or rocky hill climbs. O.E.M. clutch master cylinder and clutch lever remain intact and fully functional; The LH brake kits mounts next to the clutch master cylinder and works in conjunction with it; Maintains full use of the clutch/clutch lever while adding a LH rear brake lever; Excellent rear brake modulation with a light lever pull; Amazing in switchback conditions; Dual-actuated system that enables brake activation with either the left hand lever or right foot pedal; Increases rider confidence; Reduces crashes; Includes master cylinder with lever, hydraulic line, and slave cylinder insert; Retains the use of the rear brake pedal; Easy to install; High quality components; Made in the U.S.A.
Pads, Rotors & Lines
Brake Line/Hose Kits for KTM, Husaberg, Husqvarna by Galfer
$52.95
– $69.95
Galfer has been leading the motorcycle industry by consistently making performance products that withstand the rigors and abuse of motocross racing and aggressive riding. Galfer's off road brake lines feature a heavy-duty stiffener sleeve over the hose to route just like the O.E.M. units. Kits come complete with banjo bolts and washers. Withstands the rigors and abuse of motocross racing and aggressive riding; Constructed from stainless steel to avoid flexing for maximum stopping power; Complete with line, fittings, banjo bolts, and crush washers for complete and easy installation; Stainless steel brake lines allow maximum feel while reducing overall braking effort; Will out-perform stock brake lines; Lifetime warranty; Pre-positioned banjos for easy installation, although adjustable as needed; Made in the USA.
Brake Rotors, Disc for KTM, Husaberg, Husqvarna by Braking
$94.95
– $104.95
BRAKING's primary objective is producing hi-quality stainless steel brake rotors. The high-carbon-content stainless steel rotors produced by BRAKING offer optimal mechanical characteristics, especially at high running temperatures. Each rotor goes through a special treatment cycle to ensure it is perfectly flat. They are also put through a precise heat treatment process while adhering to the highest ISO standards. These treatments offer a high coefficient of friction while minimizing the amount of wear on the brake pads. Efficient design utilizes all the brake pad's surface evenly and eliminates the need for lightening holes that weaken rotors; Provides maximum stopping power; Remains perfectly flat and true; Manufactured from high carbon content stainless steel.
Brembo Rear Brake Pads for KTM, Husaberg, Husqvarna by Toyo
$69.95
Toyo brake pads are a premium high-performance sintered metal brake pad designed specifically for off-road and motocross racing applications. These brake pads deliver maximum stopping power in wet or dry conditions and include a backing plate with phenolic insulator to reduce heat transfer and brake fade. High-performance sintered metal compound; Specially formulated for quick bed-in time and immediate response; Phenolic heat shield/insulator backing reduces brake fluid overheating and brake fade or failure; Vaccuum-press furnace production ensures a consistent density throughout the entire pad; Excellent wet or dry braking performance; Progressive feel; Exact O.E.M replacement; Made in Japan.
Disc Brake Wave Rotors for KTM, Husaberg, Husqvarna by Dirt Tricks
$114.95
The Dirt Tricks brake rotors are the ultimate combination of durability, wear resistance, faster cooling rate and stopping power. They are incredibly strong and will resist bending unlike anything else on the market today plus black zinc plating to prevent rusting. Every rotor includes a 1 YEAR WEAR WARRANTY! Like Dirt Tricks sprockets, if you want the toughest race products, choose what professionals race. 2-3 times higher tensile strength than OEM rotors, resulting in much higher resistance to bending and wear; Made of heat treated alloy steel which provides higher stopping friction, therefore 25% less braking effort; Three times the cooling rate of stainless steel rotors; 1 year wear guarantee; Made in the U.S.A.
Floating Disc Brake Rotors for KTM 690/950/990 by Warp 9
$130.00
– $150.00
Warp 9 disc brake rotors are laser-cut out of a high-carbon content 410 stainless steel, lap cross-hatch ground, heat-treated then mounted on a floating black steel carrier for durability and strength. The floating pins are an oversized CNC machined stainless rivet with stainless wave washer to ensure these rivets will not crush like more traditionally used steel pressed rivets. High temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look. Designed for excellent brake performance Precision laser-cut out of a high-carbon content 410 stainless steel for ultimate performance; Lap cross-hatch ground for trueness; Heat-treated then mounted on a floating black steel carrier for durability and strength; Over-sized CNC machined stainless steel floating pins; High temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look; Designed for ABS and non-ABS models; Front = 300mm diameter, rear = 240mm, Thickness = 5mm; High quality for a fair price.
Odometer Magnet Kit for KTM, Husaberg, Husqvarna
$14.50
Includes magnet & circlip; Fits KTM, Husaberg, '14-'15 Husqvarna, Dirt Tricks, Braking front rotors.
RC-1 Works Brake Pads for KTM, Husaberg, Husqvarna by Renthal
$34.95
Renthal's RC-1 Works brake pads are a premium high-performance sintered metal brake pad designed specifically for off-road and motocross racing applications. These brake pads deliver maximum stopping power in wet or dry conditions. High-performance sintered metal compound made from 9 different materials helps reduce brake fade; Specially formulated for quick bed-in time and immediate response; Ceramic heat shield backing reduces brake fluid overheating and brake fade or failure; Inter-granular graphic structure helps prevent brake noise; Vaccuum-press furnace production ensures a consistent density throughout the entire pad which maintains a high performance level for the entire pad life; Excellent wet and dry braking performance; Progressive feel; Made in England.
Rotor Bolt Kit for KTM, Husaberg, Husqvarna by Bolt
$9.95
Be sure your dirt bike is in safe working order and the rotor stays tight on your KTM/Husaberg/Husqvarna with quality rotor bolts. This kit features medium strength threadlock pre-applied to the rotor bolts. Bolt Motorcycle Hardware meets or exceeds OEM hardware and is made out of quality materials in the USA. (12) M6x13mm rotor bolts; O.E.M. style; Includes bolts for front and rear rotor installation; Includes pre-applied medium threadlock; Made in the U.S.A.
Solid Rear Brake Rotor for KTM, Husaberg, Husqvarna by Dirt Tricks
$114.95
The Dirt Tricks solid rear brake rotor is the ultimate combination of durability, wear resistance, faster cooling rate and stopping power. They are incredibly strong and will resist bending unlike anything else on the market today plus black zinc plating to prevent rusting. Every rotor includes a 1 YEAR WEAR WARRANTY! Like Dirt Tricks sprockets, if you want the toughest race products, choose what professionals race. 2-3 times higher tensile strength than OEM rotors, resulting in much higher resistance to bending and wear; Made of heat treated alloy steel which provides higher stopping friction, therefore 25% less braking effort; Three times the cooling rate of stainless steel rotors; 1 year wear guarantee; Made in the U.S.A.
Sport Carbon-X RED Brake Pads for KTM, Husaberg, Husqvarna by EBC
$29.95
Although the Carbon-X pad will not outlast a sintered copper brake pad, it has the unique benefit of lower heat generation, heat transfer and a more consistent feel. When riding off-road in fast dry conditions such features are a major benefit. In our years of listening to the faster riders we have seen cases where the rear brake rotor can be glowing red in night rides which shows just how hot trail braking can get a rotor. Stopping this heat from getting to the bikes hydraulics is greatly assisted by using a carbon based pad such as the X. Consistent and progressive feel; Lowest heat generation; Reduces rotor wear.
Pedal
Billet Brake Pedal for KTM 690
$165.00
The stock KTM 690e,690r brake pedal is known to bend and snap off easily leaving you without a rear brake when you need it most. The Clean Speed Engineering pedal is machined from tough aircraft grade billet aluminum, has a significantly larger cross section for increased strength, and two sealed ball bearings for smoother pivot action and longer life.
Brake Pedal Plate for KTM, Husaberg, Husqvarna, Beta
$34.95
The KTM, Husaberg, Husqvarna brake pedal plate has large, aggressive teeth with mud clearing grooves. A positive draft center design ensures great grip in even the worst riding conditions. 3 mounting positions offer adjustability to match all boot sizes. Made of tough aircraft grade billet aluminum. Large & aggressive teeth; Positive draft center design to clear mud; 3 mounting positions; CNC machined billet aluminum; Durable & light weight; Affordable; High bling factor; Available in orange, black, blue; Made in the U.S.A.
Brake Pedal Plate w/ adjustable & replaceable cleats for KTM,Husaberg by STR
$39.95
The KTM, Husaberg, Husqvarna brake pedal plate has adjustable and replaceable cleats that give two pedal height positions. It is beveled along the inside to prevent a clutch cover puncture and is mounted with quality rounded head allen bolts and drilled for a brush cable attachment. Made of tough aircraft grade billet aluminum. Adjustable pedal height; 2 sets of cleats included (low & high position); Durable; Affordable; High bling factor; Available in orange & blue. Made in the U.S.A.
Cameras & Accessories
Battery BacPac 3+ by GoPro
$49.99
Battery BacPac attaches to your GoPro camera to increase battery life. It's perfect for long-duration time-lapse photo sessions, endurance motorsports racing or any application where you need extended battery life. LCD clearly indicated battery level and charging status. Charges by plugging into any USB power source and comes with USB charging cable. Compatible with HERO3+, HERO3, HD HERO2 models. Included: USB Cable; Standard BacPac Waterproof door; Standard BacPac Skeleton door; Slim Waterproof BacPac door; Slim Skeleton BacPac door; Straight arm extension; Protective plastic case; LCD window displays battery level or charging status; LED light displays recording status.
Chesty by GoPro
$39.99
Mounting your GoPro camera chest height provides a much more immersive experience when later viewing your adventure. The chest mount harness positions the camera in a way that you can see arms paddling, ski poles moving and handlebars twisting. It is compatible with all GoPro quick-release cameras and will adjust to fit almost any size chest. Chest harness provides a great alternative camera mount to the traditional helmet mount. Record video adventures from a lower perspective that captures more movement and body activity. One-size-fits most adjustability.
Curved & Flat Adhesive Mounts by GoPro
$19.99
Easily attach your GoPro to curved and flat surfaces with these industrial-strength waterproof adhesive mounts. Can be removed by heating adhesive bond with a hair dryer then peeling off mount. Compatible with a wide variety of curved and flat surfaces; Industrial-strength adhesive ensures secure mounting; Removable by applying heat to adhesive bond and peeling off mount.
HD Hero3 Plus Black Edition Camera by GoPro
$399.99
A company always on the move, GoPro is back and with a new and improved HD Hero3. Called the Hero3+ Black Edition, this new GoPro is 20 percent smaller, 33 percent sharper and boasting a 30 percent increase in battery life. And with a fine-tuned low light mode and 1080 SuperView mode, this is a camera to achieve professional quality footage of any motorcycle adventure you take. No matter where you mount it or if you ride moto or street, GoPro offers the finest motorsports camera available today. New Features: 20% smaller and lighter housing (waterproof to 131'/40m); SuperView video mode captures the world's most immersive wide angle perspective; Auto Low Light mode intelligently adjusts frame rate for stunning low light performance; 33% improved image sharpness and reduced distortion; Faster built-in Wi-Fi for enhanced connectivity to the Wi-Fi; Remote (included) and GoPro App; 30% longer battery life; Wireless camera software updates via the GoPro app; Upgraded audio performance.
HD Hero3 Plus Silver Edition Camera by GoPro
$299.99
Not only is the HERO3+ Silver Edition 20% smaller and lighter than previous models, it's 2x more powerfulmaking it GoPro's most advanced Silver Edition camera yet. Wearable, gear-mountable and waterproof to 131'/40m, it captures professional-quality video at up to 1080p60 and 10MP photos at up to 10 frames per second. With faster built-in Wi-Fi, enhanced low-light performance and 25% longer battery life, the HERO3 + Silver Edition makes capturing and sharing your life easier than ever. What's New: 20% smaller and lighter housing (waterproof to 131'/40m); 2x faster image processor enables 1080p60 and 720p120fps video; Enhanced low-light performance; Improved image sharpness and reduced distortion; Faster built-in Wi-Fi for enhanced connectivity to the Wi-Fi emote (sold separately) and GoPro app; Wireless camera software updates via the GoPro app; 25% longer battery life; Upgraded audio performance.
Helmet Front Mount by GoPro
$12.99
Mount your GoPro to the front of your helmet in a headlamp-like position. Capture forward-facing footage, or adjust the extendable arm so the camera is facing you for self-portrait videos and photos. The mount can be removed by heating the adhesive bond with a hair dryer then peeling off mount. Mounts to the front of most helmets; Capture forward-facing footage or self-portrait photos and videos; Can be removed by applying heat to adhesive bond; Warranty: 1 Year.
Hero 3 Rechargable Battery by GoPro
$19.99
Use this 1050 mAH lithium-ion rechargeable battery as a spare or replacement for your HERO3 & Hero3 Plus. 1050 mAh provides reliable power. Rechargeable design.
Side Mount by GoPro
$12.99
Attach your GoPro camera to the side of helmets, vehicles, gear and more. 3-way pivot adjustability makes aiming easy. Kit includes: Side mount; 3-way pivot; Curved adhesive mount.
Suction Cup Mount 2 by GoPro
$39.99
Attach your GoPro to cars, boats, motorcycles and more. This industrial-strength Suction Cup mount is proven at speeds of 150+ mph and engineered for stability and a broad range of motion. Adjustable arms allow for ultra-compact mounting. Includes a standard base and a quick release base for moving conveniently between shots and locations. For maximum holding strength, attach to a clean surface. Engineered to provide a broad range of motion and stability; Quick release base makes moving between shots and locations quick and convenient.
The Frame by GoPro
$39.99
The Go Pro The Frame mount is the smallest, lightest way to mount your HERO3 camera. It comes with assorted mounting hardware, 1 Flat Adhesive Mount, and 1 Curved Adhesive Mount. Sleek frame design for low profile, compact mounting; Lens cap protects camera lens; Engineered for optimal sound at speed; Compatible with LCD Touch BacPacTM and second generation Battery BacPacTM; The Frame mount is NOT waterproof and not optimized for use in extreme conditions where dirt and sharp objects can damage the camera lens. In the Box: Standard Frame, BacPac Frame, Lens Cover, Assorted Mounting Hardware, 1 Flat Adhesive Mount, and 1 Curved Adhesive Mount.
Chassis
Axle Pull
Axle Pull Handle for WP, KTM & Husaberg
$19.95
– $27.95
Front axle quick pull handles make front wheel removal/installation a lot faster and much easier. No more trying to get a grip on the axle to pull it out, just grab the handle and pull. Only takes seconds to mount. Slide the handle into the blind end (non-threaded) of the axle and tighten the split-bevel expansion anchor done. Available for KTM, Husaberg & Husqvarna models including the KTM 125-530, 640 Adv., 690, 950SE, and 950/990 Adventure. Made of durable billet aluminum; Quick & easy installation; Faster & easier axle removal.
Front & Rear Axle Pull Handle for Yamaha/Kawasaki/Honda/Suzuki/KTM
$19.95
Front axle quick pull handles make front wheel removal/installation a lot faster and much easier. No more trying to get a grip on the axle to pull it out. Just grab the handle and pull. Only takes seconds to mount.
Bearings
Linkage Bearing Rebuild kit for KTM, Husqvarna 125-450
$84.95
Contains all of the bearings, seals, bearing sleeves needed to rebuild the swingarm linkage to factory specs; Most complete kit in the industry.
Lower Shock Heim Joint Bearing Kit for KTM, Husaberg
$29.95
This kit includes a long lasting, high quality heim joint, 2 seals, and 2 spacer inserts. It fits in the swingarm where the shock attaches. heim joint; 2 seals; 2 spacers.
Steering Head Bearing Kits for KTM, Husaberg & Husqvarna
Swingarm Bearing Rebuild Kit for KTM, Husaberg, Husqvarna
$49.95
– $69.95
Contains all of the bearings, seals, bearing sleeves, and spacers required to rebuild a swing arm to factory specifications; Manufactured from 52100 bearing steel for improved performance and extended life; Features Teflon D coated seals for superior performance.
Unshock Shock & Fork Thrust Bearing Kits for WP/Ohlins/KTM/Husaberg, Husqvarna
$27.49
– $44.95
The Unshock Thrust Bearing Kits are just the ticket to improve your shock and fork action. Designed to reduce binding in the spring as it compresses. The Unshock Thrust Bearing Kits are a long overlooked inexpensive and easy to install improvement to your WP/Ohlins/KTM/Husaberg front and rear suspension. Eases pre-load adjustment; Prevents spring binding during compression and rebound; Sealed to prevent contamination; Provides consistent spring action; Includes two thrust washers, two o-rings, and one thrust bearing (shock kit only); Improves shock/fork action; Easy to install.
Upper Shock Bearing/Heim Bearing for KTM, Husaberg, Husqvarna
$24.95
Contains the upper heim bearing, seals, and spacers needed to replace the upper heim bearing.
Wheel Bearing Kit for KTM, Husaberg by Enduro Engineering
$39.95
– $52.95
High quality, long lasting, double sealed wheel bearings plus outer hub seals and axle spacers are included. The Enduro Engineering KTM, Husaberg wheel bearing kit is an economical yet high quality solution to the high priced o.e.m. bearings Includes: Sealed wheel bearings; Hub seals; Axle spacers.
Chain Guides
Chain Guide for KTM 950 (SE) Super Enduro by BRP
$67.90
The BRP (Billet Racing Products) polymer chain guide offers increased strength, durability and performance over O.E.M.. Available in black. Exceptional impact resistance; Superior wear resistance; Virtually indestructible; Open channel design easily disperses sand, mud, and dirt; Accommodates wide heavy duty o-ring chains; 1 year warranty.
Chain Guide for KTM by TM Designs
$69.95
The guide uses our latest custom plastic formula with the lowest co-efficiency of drag for increased power over any other chain guide setup. UV additives guarantee the plastic will not fade or dry out under the sun. Oversize sprockets & O-ring chains are not a problem. Get the same part as team Red Bull KTM who won every national off road series championship in 2007.
Chain Guide for KTM, Husaberg, Husqvarna by BRP
$76.95
The BRP (Billet Racing Products) Extreme polymer chain guide offers increased strength, durability and performance over O.E.M. and is now available in solid black, blue and orange for KTM and Husaberg models. Features: Exceptional impact resistance; Superior wear resistance; Virtually indestructible; Open channel design easily disperses sand, mud, and dirt; Accommodates wide heavy duty o-ring chains; 1 year warranty.
Factory Edition 2 Chain Guide for KTM, Husaberg, Husqvarna, Sherco by TM
$89.95
The TM Designs Factory Edition 2 chain guide has a 100% new patented design. 8 months of testing, used and endorsed by Red Bull KTM and the KTM Factory off road race team. The TM Designs custom plastic RMS (return memory) formula will not break like stock and the new mechanical shape and design reinforces and adds support to the weak swingarm mounting brackets. Every component can now be individually replaced making this guide the ultimate long term investment. Constructed with indestructible "Zero Chain Drag" plastic. Delivers smooth performance and consistent chain tension. Open design disperses sand and dirt through the bottom. All necessary mounting hardware is included. 1-year unconditional guarantee. Accepts oversize chain and sprockets
Factory MX Chain Guide for KTM, Husaberg, Husqvarna, Sherco by TM
$61.95
This chain guide has a 100% new patented design.Used and endorsed by Red Bull KTM and the KTM Factory off road race team. The TM Designs custom plastic RMS (return memory) formula will not break like stock and the new mechanical shape and design reinforces and adds support to the weak swingarm mounting brackets. Every component can now be individually replaced making this guide the ultimate long term investment. Constructed with indestructible "Zero Chain Drag" plastic. Delivers smooth performance and consistent chain tension. Open design disperses sand and dirt through the bottom. All necessary mounting hardware is included. Accepts oversize chain and sprockets. Our new Super light weight guide is still stronger than stock and gives unprecedented sprocket protection. Our Motocross/Supercross rear chain guide for the KTM is a huge 70 plus grams lighter than the heavy stock KTM guide. The only guide that strengthens and protects the stock low strength cast mounting brackets that are prone to snapping upon heavy impact! 1-Year unconditional breakage warranty on the body in the USA only. The only guide to be used exclusively by the KTM Factory race teams worldwide. Recommended by Dirt Bike, Dirt Rider, Transworld MX and Motocross Action magazines! 75 grams lighter than the TM KT3 chain guide.
GP MX Chain Guide for KTM, Husaberg, Husqvarna, Sherco by TMD
$89.95
Super slim narrow profile reduces the chance of guide skimming ruts and berms causing damage; Ultra compact configuration reduces un-sprung weight by a whopping 15 grams compared to stock; Wear pad is replaceable and longer than stock to prevent chain from possibly derailing; The wear pad and guide angle is setup for oversize sprockets reducing excessive wear on chain plates; TMD's exclusive "return memory formula: UV protection and oil is included for low drag and long term service; Uses stock hardware and is rated as a 5 stars out of 5 product from the leading motocross magazines; The only chain guide with a perfect match O.E.M. color. KTM orange, black, and new 2014 Husqvarna dark blue; Not recommended for serious heavy duty off road racing . Use our proven RCG-KT3 guide with 6 straight worldwide championships. One 2014 championship already produced by France's elite National Motocross Champion Sebastion Pourcel. One year breakage warranty.
Damper Kits
Dampers and accessories
4 Position Damper Mount for KTM/Husaberg/Husqvarna by Dirt Tricks
$129.00
Dirt Tricks 4-position stabilizer mounting kit fits 2012-2014 KTM/Husaberg/'14 Husqvarna. This kit features a two piece clamp design which bolts securely to the frame neck of your bike. You do not need to remove your top triple clamp for installation! Additionally, we have added a perfectly sized counter-bore to the 2-piece clamp which clears your OEM dust seal. -Again, no removal needed! The 4-postion bar mount allows you to run any one of 4 bar positions without the need for purchasing new parts. The bar mount is 180 degrees reversible and drilled with 4 sets of holes which correspond to each one of the KTM/Husaberg/Husqvarna bar positions. The bar mount features a slim, low profile design. Works great with O.E.M. or after market handlebars including Fasstco's Flexx Bars. Due to its ease of installation and overall functionality, this is the best KTM/Husaberg/Husqvarna stabilizer mounting kit on the market today. Available in orange anodize and machined from 6061 Aluminum. Made in the USA!
Damper Frame Bracket Tower for KTM, Husaberg, Husqvarna by Scotts
$39.95
– $86.95
Weld-on (must be welded on to the frame); Bolt-on for sub-mounted dampers; Bolt-on for top-mounted dampers; Bolt-on mounts include bearing cover.
Damper Link Arm Puller by Scotts
$14.95
The Scotts link arm puller makes pulling the link arm from your Scotts stabilizer a breeze. This small but important tool is a great addition to any service shop, mechanic or or home tuner. Easy to use; first remove the nut, then evenly insert small screws into existing holes in link arm, tighten the 8mm allen bolt with a 6mm allen wrench to remove the link arm. Using the puller tool instead of prying on arm will prevent damage to your Scotts stabilizer. Easy to use; Prevents damage to damper unit; Made in the U.S.A.
Steering Damper/Stabilizer by Scott
$322.95
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. It is a compact, fully adjustable, hydraulic shock absorbing damper that mounts to your steering head area right above or below your handlebar mount. By helping to stabilize the front end of your motorcycle, the rear of the motorcycle will track straighter allowing the rest of your suspension to work better. In addition, the Scott's Steering Stabilizer eliminates that sudden "jolt" affect of having the handlebars pulled from your hands after unknowingly hitting something unforeseen like rocks, tree roots or rain ruts. It has also helps to minimize rider fatigue and the dreaded arm-pumping situation that occurs while wrestling the front end of your bike. Once mounted, it dramatically reduces the unwanted phenomenon known as "head-shake" that is commonly found on all off-road production motorcycles. It helps keep your motorcycle going straight in the whoops and smooths out those rough sections by preventing those handlebar wrenching jolts.
This is a must-have for KTMs and Husabergs using top mount or sub mount Scotts or GPR steering stabilizers. It keeps the throttle cables away from the stabilizer, handlebar clamp, and handlebars, preventing wear and potentially dangerous cable snags. The tower mounted guides are machined from billet 6061 Aluminum and the sub mount guides are machined from a wear resistant, tough, co-polymer plastic. Unique split design makes installation a breeze without removing the throttle cable(s). All mounting hardware is stainless steel to prevent corrosion. Top mount (above bars) Scott's dampers, with a bolt-on tower, use 9/16"; Top mount (above bars) Scotts dampers with a weld-on towers use 1/2"; For Scott's sub-mount (below bars) dampers, ONLY use the sub-mount cable guide; GPR V1, V2, V3 dampers use 12" GPR V4 dampers use the V4 guide.
Gas Gas Damper Kits
Scotts Steering Damper Kit for Gas Gas
$439.00
– $599.00
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another.
Honda Damper Kits
Scotts Steering Damper Kit for Honda CRF250/450R&X
$439.00
– $499.00
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; This is a complete kit including damper, bar mount or sub-mount, frame mount, and all mounting hardware.
Husaberg Damper Kits & Mounting Kits
Damper Frame Bracket Tower for KTM, Husaberg, Husqvarna by Scotts
$39.95
– $86.95
Available frame brackets types: Weld-on (must be welded on to the frame); Bolt-on for sub-mounted dampers; Bolt-on for top-mounted dampers; Bolt-on mounts include bearing cover.
Rubber Mounted Damper Sub-Mount Adapter for Husaberg
$162.00
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the USA.
Rubber Mounted Sub-Mount Damper Mounting Kit for Husaberg by BRP
$227.95
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the USA.
Rubber Mounted Sub-Mount Scotts Damper Kit for Husaberg by BRP
$532.00
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the USA.
Scott's Steering Damper Kit for Husaberg
$428.00
– $466.00
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Made in the USA.
Scotts Damper Mount/Handguard Mount for KTM/Husaberg/Husqvarna/Beta by BRP
$127.95
The BRP Combination Scotts Steering Stabilizer & Handguard Mount includes 3 sets of damper mounting tabs to accommodate handlebar positions #2 and #3 for ALL '00 '14 KTM 125-530cc models, ALL '09-'14 Husaberg 250-570, ALL '14 Husqvarna 250-501 and ALL '11-'13 Beta 350-520. BRP hand guard mounts are proven to be the strongest system for mounting your hand guards. Comes complete with: (3) Sets of color coded damper mounting tabs to accommodate position 2 & 3; (2) M8 x 25 flange head bolts for mounting handguards; (4) M8 x 30 socket head bolts to mount bar clamp to stock handlebar perches.
This is a must-have for KTMs and Husabergs using top mount or sub mount Scotts or GPR steering stabilizers. It keeps the throttle cables away from the stabilizer, handlebar clamp, and handlebars, preventing wear and potentially dangerous cable snags. The tower mounted guides are machined from billet 6061 Aluminum and the sub mount guides are machined from a wear resistant, tough, co-polymer plastic. Unique split design makes installation a breeze without removing the throttle cable(s). All mounting hardware is stainless steel to prevent corrosion. Application: Top mount (above bars) Scott's dampers, with a bolt-on tower, use 9/16"; Top mount (above bars) Scotts dampers with a weld-on towers use 1/2"; For Scott's sub-mount (below bars) dampers, ONLY use the sub-mount cable guide; GPR V1, V2, V3 dampers use 12" GPR V4 dampers use the V4 guide.
Husqvarna Damper Kits & Mounting Kits
Damper Frame Bracket Tower for KTM, Husaberg, Husqvarna by Scotts
$39.95
– $86.95
Available frame brackets types: Weld-on (must be welded on to the frame); Bolt-on for sub-mounted dampers; Bolt-on for top-mounted dampers; Bolt-on mounts include bearing cover.
Scotts Damper Mount/Handguard Mount for KTM/Husaberg/Husqvarna/Beta by BRP
$127.95
The BRP Combination Scotts Steering Stabilizer & Handguard Mount includes 3 sets of damper mounting tabs to accommodate handlebar positions #2 and #3 for ALL '00 '14 KTM 125-530cc models, ALL '09-'14 Husaberg 250-570, ALL '14 Husqvarna 250-501 and ALL '11-'13 Beta 350-520. BRP hand guard mounts are proven to be the strongest system for mounting your hand guards. Comes complete with: (3) Sets of color coded damper mounting tabs to accommodate position 2 & 3; (2) M8 x 25 flange head bolts for mounting handguards; (4) M8 x 30 socket head bolts to mount bar clamp to stock handlebar perches.
This is a must-have for KTMs and Husabergs using top mount or sub mount Scotts or GPR steering stabilizers. It keeps the throttle cables away from the stabilizer, handlebar clamp, and handlebars, preventing wear and potentially dangerous cable snags. The tower mounted guides are machined from billet 6061 Aluminum and the sub mount guides are machined from a wear resistant, tough, co-polymer plastic. Unique split design makes installation a breeze without removing the throttle cable(s). All mounting hardware is stainless steel to prevent corrosion. Application: Top mount (above bars) Scott's dampers, with a bolt-on tower, use 9/16"; Top mount (above bars) Scotts dampers with a weld-on towers use 1/2"; For Scott's sub-mount (below bars) dampers, ONLY use the sub-mount cable guide; GPR V1, V2, V3 dampers use 1/2" GPR V4 dampers use the V4 guide.
KTM Damper Kits & Mounting Kits
Rubber Mounted Damper Sub-Mount Adapter for KTM
$171.00
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the USA.
Rubber Mounted Sub-Mount Damper Mounting Kit for KTM by BRP
$237.45
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the USA.
Rubber Mounted Sub-Mount Scotts Damper Kit for KTM by BRP
$541.50
The all new BRP rubber mounted sub-mount for Scotts dampers is innovative and effective in reducing engine and chassis vibrations felt in the handlebars. This stellar new product combines the sub-mount system with 8 Poly-Urethane elastomers to reduce and isolate vibrations and increase rider comfort. It mounts to the existing rear handlebar mounting holes and allows you to run in position 3, which is the most common and popular position. Sub-mount/below the bar mounting; Reduces engine & chassis vibrations; Softens the harsh spike when hitting rocks and roots; Increases rider comfort; Approximately 1 taller bar position; Lower bend bars can be used to compensate for additional height; Reduces rider fatigue; Easy installation; Mounts to o.e.m. (stock) triple clamp ONLY; Made in the U.S.A.
Scott's Steering Damper Kit for KTM 950 & 990 Adventure & Adventure S
$409.00
– $664.95
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. BRP/Scotts sub-mount kits come with a BRP triple clamp, sub-mount adapter, Scotts stabilizer and bolt-on tower. Priced as as a package to save you money. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Increased high-speed stability; Made in the U.S.A.
Scott's Steering Damper Kit for KTM 950/990 SM
$664.95
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. BRP/Scotts sub-mount kits come with a BRP triple clamp, sub-mount adapter, Scotts stabilizer and bolt-on tower. Priced as as a package to save you money. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Made in the U.S.A.
Scott's Steering Damper Kit for KTM 950/990 Super Duke
$474.00
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. BRP/Scotts sub-mount kits come with a sub-mount adapter, Scotts stabilizer and bolt-on tower. Priced as as a package to save you money. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Made in the U.S.A.
Scott's Steering Damper Kit for KTM 950SE Super Enduro
$409.00
– $664.95
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. BRP/Scotts sub-mount kits come with a BRP triple clamp, sub-mount adapter, Scotts stabilizer and bolt-on tower. Priced as as a package to save you money. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Made in the U.S.A.
Scotts Damper Mount/Handguard Mount for KTM/Husaberg/Husqvarna/Beta by BRP
$127.95
The BRP Combination Scotts Steering Stabilizer & Handguard Mount includes 3 sets of damper mounting tabs to accommodate handlebar positions #2 and #3 for ALL '00 '14 KTM 125-530cc models, ALL '09-'14 Husaberg 250-570, ALL '14 Husqvarna 250-501 and ALL '11-'13 Beta 350-520. BRP hand guard mounts are proven to be the strongest system for mounting your hand guards. Comes complete with: (3) Sets of color coded damper mounting tabs to accommodate position 2 & 3; (2) M8 x 25 flange head bolts for mounting handguards; (4) M8 x 30 socket head bolts to mount bar clamp to stock handlebar perches.
Scotts Steering Damper Kit for KTM 690E/R Enduro & SMC
$599.00
The Scotts/BRP Rubber Mount Sub-Mounted Steering Damper kit is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. Features: Each mounting kit is bike specific; Complete kit that includes the Scotts damper and ALL necessary mounting brackets and mounting hardware; Easy to install includes installation and tuning manual; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; Fits stock triple clamps; Raises bars 1 inch (25mm); Made in the U.S.A.
Scotts Steering Damper Top-Mount Kit for KTM 125-530
$428.00
The Scotts Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. It is a compact, fully adjustable, hydraulic shock absorbing damper that mounts to your steering head area right above or below your handlebar mount. By helping to stabilize the front end of your motorcycle, the rear of the motorcycle will track straighter allowing the rest of your suspension to work better. In addition, the Scott's Steering Stabilizer eliminates that sudden "jolt" affect of having the handlebars pulled from your hands after unknowingly hitting something unforeseen like rocks, tree roots or rain ruts. It has also helps to minimize rider fatigue and the dreaded arm-pumping situation that occurs while wrestling the front end of your bike. Once mounted, it dramatically reduces the unwanted phenomenon known as "head-shake" that is commonly found on all off-road production motorcycles. It helps keep your motorcycle going straight in the whoops and smooths out those rough sections by preventing those handlebar wrenching jolts.
Yamaha Damper Kits
Scotts Steering Damper Kit for Yamaha
$439.00
– $549.00
The Scott's Steering Damper is the industry leader for quality, performance, and customer service. It is by far the best damper on the market. Features: Each mounting kit is bike & position specific; Includes all necessary mounting hardware and a detailed manual Easy to install; 3 damping fully adjustable damping circuits (high speed, low speed, sweep); Used and endorsed by every off-road magazine; Highest quality and best customer support; Easily moved from one motorcycle to another; This is a complete kit including damper, bar mount or sub-mount, frame mount, and all mounting hardware.
Footpegs
2.3 Platform Footpegs for KTM, Husaberg, Husqvarna, Beta by Pro Taper
$169.95
Pro Taper focuses on developing products that are built for racing and the 2.3 Platform footpegs give that and more; Durable 7075 hard anodized billet aluminum cleats with a precision cast stainless steel base; Standard height cleats have an arch shape that give the Pro Taper 2.3 foot pegs a unique and highly effective traction platform. Unique ability to change height with replaceable -5 mm and +5 mm cleats that Pro Taper offers separately; All mounting hardware is included; Only the standard height cleats are included; Sold as a pair.
Billet Footpegs for KTM, Husaberg, Husqvarna, Beta by Warp 9
$99.50
Light weight 6065 T6 billet aluminum; CNC machined for perfect fitment; Extra wide platform for comfort and secure grip; Exclusive "X" bridge adds 2 center removable teeth for added grip; Footpeg Size is 57mm wide and 75mm long; Stainless steel teeth; Available in orange and black.
F3 Evo 3 Footpegs for KTM, Husaberg, Husqvarna, Beta by Fastway
$119.95
The most versatile footpeg system on the planet! Straight from the race track, the F3 footpegs feature Fastway's patented threaded pin-style cleats. These large platform pegs offer sure-footed confidence, maximum grip, and adjustability. The Universal Collar System is designed for ergonomics and adjustability. The system allows you to choose from Standard or Lowboy (1/2 lower) seat-to-peg height positions , giving you a custom fit between you and your ride. In addition the FKMS (Fast Kamber Mounting System) allows you to adjust the upward and downward tilt of the pegs. Massive platform for comfort and stability; Standard or Lowboy position (1/2 lower); Patented teeth for maximum control; Ergonomically adjustable; Camber and height adjustable; 17/4 stainless steel construction; Fully rebuildable; Replaceable cleats.
F3 Replacement Cleat Set for Fastway Evo 2, Evo 3 & Evo Air Footpegs
$19.95
The replacement cleat set is a direct replacement for the cleats that come standard in Fastway F3 pegs. The standard pin cleats feature our threaded-pin style set screw cleat. Kit includes both 10mm and 12mm length, to do a full peg set of each. Includes enough for both Fastway Evo III pegs and Evo Air pegs. Fits Fastway Evolution II, III Series and Evo Air footpegs; All Evolution II, III threaded-pin style cleats are interchangeable between footpeg models; Kit includes 22 cleats, enough to replace all cleats on a set of pegs (11 cleats per side), and a handy insertion tool; Includes both 10mm and 12mm length.
F6 Replacement Cleat Set for Fastway Evo 2, Evo 3 & Evo Air Footpegs
$19.95
The F6 replacement cleat set is a spike style replacement for the cleats that come standard in Fastway F3 pegs. The F6 cleats feature a threaded spike style cleat. Kit includes enough to do a full peg set of each. Includes enough for both Fastway Evo III pegs and Evo Air pegs. Fits Fastway Evolution II, III, and Evo Air footpegs; Kit includes 22 spike cleats, enough to replace all cleats on a set of pegs (11 cleats per side).
Mark 3 Pivot Pegz for KTM,Husaberg, Husqvarna
$162.95
The new Mark 3 Pivot Pegz® are now available and have taken it to a whole new level with a mega wide 60mm platform. Due to the pivoting nature of Pivot Pegz you can have the best of both worlds, a mega wide 60mm platform and easy access to the gear shift and rear brake lever, this is due to the fact that the Pivot Pegz platform pivots and opens up access to the lower controls. This isn't your average footpeg. Not only do you get a mega wide platform but a state of the art grip pattern, platform design and spring loaded pivoting action. That means you get enhanced grip and load distribution as well as reduced impact and fatigue. The new Mark 3 Pivot Pegz are also designed to reduce mud packing in the peg. Pivot Pegz® have been designed and built to last and are backed by an exclusive LIFETIME WARRANTY. Pivot Pegz are designed using high tech 3D computer modeling software and are a precision built product. They are formed by using high strength aerospace grade stainless steel before being CNC machined and double heat treated. Pivot Pegz® are then electro-polished to a high grade luster before finally having the exterior hand polished to a mirror finish which highlights the embossed logo and really makes Pivot Pegz® stand out in the crowd.
MSR Standard Footpegs for KTM, Husaberg, Husqvarna, Beta by MSR HP
$109.95
MSR Standard Footpegs are made from durable, corrosion resistant stainless steel with an exclusive arched cleat design for enhanced positioning and control. A 55mm wide platform offers comfort and aggressive cleats keep the riders feet firmly planted in all weather conditions. Available in stock position or 13mm (1/2) rearward offset. Stainless steel cast construction resists rust and corrosion for added life and durability; Exclusive camber/arched cleat design aids in enhanced rider positioning and control; Features a 55 mm wide platform for comfort and protection; Aggressive peak cleat pattern keeps rider firmly planted in all weather conditions; Perfect for off-road and motocross riding and racing; Open flow-thru design keeps mud and rocks from building up; 13 mm (1/2) rear offset for larger footed riders or to achieve a more rearward position; Sold as a pair; Made in the U.S.A.
Xtreme Titanium Footpegs for Honda, Kawasaki, Suzuki, Yamaha by Raptor
$339.95
Raptor Titanium produces high-quality, hand-welded footpegs that are manufactured in the UK and ridden all around the world. Used by teams such as KTM Red Bull USA riders Ryan Dungey, Ken Roczen and Marvin Musquin. The revolutionary 24 tooth, maximum grip, anti-clog designs are the only fully factory fabricated titanium footpegs on the market. Manufactured to the highest standards from aerospace grade titanium, they only use the latest manufacturing techniques to produce the strongest welds, eliminating stress and corrosion. The Raptor Titanium Company set the standards with the bigger platform and greater surface area which provides the rider with additional grip! Super lightweight = 410 grams; 57mm wide; Hand welded; Used by Factory KTM Red Bull USA, Geico Powersports, Hart & Huntington Suzuki, and Rockstar Energy Suzuki Made in the UK.
Xtreme Titanium Footpegs for KTM, Husaberg, Husqvarna, Beta by Raptor
$339.95
Raptor Titanium produces high-quality, hand-welded footpegs that are manufactured in the UK and ridden all around the world. Used by teams such as KTM Red Bull USA riders Ryan Dungey, Ken Roczen and Marvin Musquin. The revolutionary 24 tooth, maximum grip, anti-clog designs are the only fully factory fabricated titanium footpegs on the market. Manufactured to the highest standards from aerospace grade titanium, they only use the latest manufacturing techniques to produce the strongest welds, eliminating stress and corrosion. The Raptor Titanium Company set the standards with the bigger platform and greater surface area which provides the rider with additional grip! Super lightweight = 410 grams; 57mm wide; Hand welded; Used by Factory KTM Red Bull USA, Geico Powersports, Hart & Huntington Suzuki, and Rockstar Energy Suzuki; Made in the UK.
Guards
Engine Guards
Clutch Case Guard for KTM, Husaberg by STR
$62.95
– $69.95
The all new System Tech Racing (STR) billet machined clutch cover guard offers better protection than any other guard on the market. This super tough guard prevents ride ending puncture damage to the clutch case and offers bling value at the same time. Billet machined from aircraft quality aluminum alloy; Stops ride ending puncture damage from the brake pedal and trail debris; Easy to install in seconds; All mounting hardware provided; Available in orange, blue & polished; Bling value; Made in the U.S.A.
Clutch Case Guard for KTM, Husaberg, Husqvarna by EE
$29.95
– $39.95
Made of durable 7075 T6 aluminum, the Enduro Engineering slave cylinder guard has more features than any other on the market. The unique design allows mud and debris to clean out, the clutch line bleeder is fully accessible, and the O.E.M. upper chain guide remains in place or is provided to help route the chain to the bottom side in the event of a chain failure. Knockdown bar included for most models; Protects the clutch slave cylinder and center case if the chain derails; Cleans out well during muddy conditions; Black anodized; Made in the U.S.A.
Clutch Case Guard for KTM, Husaberg, Husqvarna by Rekluse
$50.00
Machined from durable 7075 T6 aluminum, the Rekluse slave cylinder guard has more features than any other on the market. The unique design allows quick and easy auto-clutch adjustments, mud and debris to clean out, the clutch line bleeder is fully accessible, and the O.E.M. upper chain guide remains in place or is provided to help route the chain to the bottom side in the event of a chain failure. Protect your Rekluse slave cylinder with this exclusive guard; Fits Rekluse adjustable and O.E.M. slave cylinder; Features an access hole for quick and easy auto-clutch adjustment; CNC machined 7075 T6 billet aluminum; Knockdown bar & chain slider included for many models; Protects the clutch slave cylinder and center case if the chain derails; Cleans out well during muddy conditions; Grey anodized; Made in the U.S.A.
Handguards & Handguard Mounts
Cycra Alloy Probend Handguard Pack with Hand Shields
$74.95
Bar Pack Includes: Probend Bars w/bumpers and Enduro Shields; For use with Fastco Handguard Hitch or BRP handguard mounts; Powergrip bar ends & hardware (mount clamps not included); CNC machined 6061 billet aluminum Probend Bars; Trademark Probend shape; Large area to accommodate hands and levers; High quality injection molded enduro style handshields; Integrated composite bumper to protect Probend Bars; Plus a new and improved bar end mount.
Link Skid
Original Link Skid for KTM, Husqvarna by Slavens
$64.95
This unique new concept in protection guards the shock clevis and shock linkage from rock damage and enables the linkage to glide over logs and boulders. Without the Slavens Link Skid, the shock clevis will catch on logs and stop the bike or throw the rider forward. Because the clevis and linkage extends well below the swingarm, it is very susceptible to expensive damage. Prevents expensive damage to the shock clevis and linkage; Allows the bike to glide over logs & boulders; Made of durable and lightweight 6061 T6 aluminum; Mounts easily & quickly in minutes; All mounting hardware included; Installation videos (see below); Tested and used by Dike Bike & Dirt Rider magazines; Colors: orange, blue, brushed; Made in the U.S.A.
Xtreme Link Skid for KTM, Husqvarna 125-501 by Slavens
$89.95
This unique new concept in protection guards the shock clevis and shock linkage from rock damage and enables the linkage to glide over logs and boulders. Without the Slavens Link Skid, the shock clevis will catch on logs and stop the bike or throw the rider forward.Because the clevis and linkage extends well below the swingarm, it is very susceptible to expensive damage. We now offer 2 link skids, the Original and the Xtreme. The Original gives great protection for most riding conditions and the Xtreme is for those that often ride extremely rocky conditions and demand the best coverage possible. The new loop design bottom plate gives added protection and durability. Prevents expensive damage to the shock clevis and linkage; Allows the bike to glide over logs & boulders; Toughest link skid available, period!!! Slavens original design tested in the Rocky Mountains since August 2010; Made of durable and lightweight 6061 T6 aluminum; Mounts easily & quickly in minutes; All mounting hardware included; Installation videos (below); Tested and used by Dirt Bike magazine; Colors: orange, blue, brushed; Made in the USA.
Radiator Guards
Radiator Braces & Guards for KTM, Husaberg, Husqvarna by 7602
$34.95
– $142.95
Super strong design resists twisting as well as side and front impacts. Can be used with a cooling fan. Optional front guard mounts directly to the radiator brace for ultimate trail protection. Provides extra frontal protection from branches and rocks. Must be used with our radiator braces. Resist twisting; Provides protection from side and front impacts; Fits with cooling fans the fan mounts directly to the radiator brace; 2 piece construction braces & guards may be purchased separately; Colors orange, blue, brushed/natural; Made in the U.S.A.
Radiator Guards by Bullet Proof Designs for Honda
$189.00
– $209.00
Machined from solid 6061-T6 billet aluminum for superior strength; Does not effect cooling or air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Each guard weighs 12 ounces.
Radiator Guards by Bullet Proof Designs for Husaberg
$195.00
– $214.00
The new Gen 2 Radiator Guards by Bullet Proof Designs offer inclusive side wings to protect the vulnerable radiator shroud mounting tabs. If the tabs are hit during even a minor tip over, several rows of the radiator core may be damaged. The new wing design prevents that damage from occurring. No other brands offer this protection. It's a Bullet Proof Designs exclusive. Machined from solid 6061-T6 billet aluminum for superior strength; Does not adversely effect cooling or restrict air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Lightweight each guard weighs 12 ounces; Made in the U.S.A. by guys that ride.
Radiator Guards by Bullet Proof Designs for KTM
$95.00
– $214.00
The new Gen 2 Radiator Guards by Bullet Proof Designs offer inclusive side wings to protect the vulnerable radiator shroud mounting tabs. If the tabs are hit during even a minor tip over, several rows of the radiator core may be damaged. The new wing design prevents that damage from occurring. No other brands offer this protection. It's a Bullet Proof Designs exclusive. Machined from solid 6061-T6 billet aluminum for superior strength; Does not adversely effect cooling or restrict air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Lightweight each guard weighs 12 ounces; Does not interfere with fan kits; Made in the U.S.A. by guys that ride.
Radiator Guards by Bullet Proof Designs for Yamaha
$189.00
– $209.00
Machined from solid 6061-T6 billet aluminum for superior strength; Does not effect cooling or air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Each guard weighs 12 ounces.
Radiator Guards for Husqvarna by Bullet Proof
$195.00
– $214.00
The new Gen 2 Radiator Guards by Bullet Proof Designs offer inclusive side wings to protect the vulnerable radiator shroud mounting tabs. If the tabs are hit during even a minor tip over, several rows of the radiator core may be damaged. The new wing design prevents that damage from occurring. No other brands offer this protection. It's a Bullet Proof Designs exclusive. Machined from solid 6061-T6 billet aluminum for superior strength; Does not adversely effect cooling or restrict air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Lightweight each guard weighs 12 ounces; Made in the U.S.A. by guys that ride.
Radiator Guards for Sherco by Bullet Proof
$197.00
– $217.00
The new Gen 2 Radiator Guards by Bullet Proof Designs offer inclusive side wings to protect the vulnerable radiator shroud mounting tabs. If the tabs are hit during even a minor tip over, several rows of the radiator core may be damaged. The new wing design prevents that damage from occurring. No other brands offer this protection. It's a Bullet Proof Designs exclusive. Machined from solid 6061-T6 billet aluminum for superior strength; Does not adversely effect cooling or restrict air flow; Mounts to frame to provide frontal and side impact protection; Lifetime original owner warranty; Lightweight each guard weighs 12 ounces; Made in the U.S.A. by guys that ride.
Skid Plates
Carbon Skid Plate by Eline for KTM,Husaberg
$154.95
The Eline KTM, Husaberg carbon fiber composite skid plates are molded to an exact shape for a perfect fit that offers complete protection. They are extremely light weight, durable, absorb vibration, and do not amplify engine or trail noises. They now feature the brilliant "Easy Mount" front mounting system that fastens to the exhaust pipe mount frame tab for quick and easy installation. The rear mounts are CNC billet machined. Composite molded for a perfect fit; Durable carbon fiber construction; Extremely lightweight; Absorbs vibration & noise; "Easy Mount" front mounting system; Made in the USA.
Mule Skid Plate for KTM 1190 Adventure
$295.00
– $319.00
Slavens Mule KTM Skid Plate is made of rugged 5mm thick 5052 aluminum and feature TIG welded engine guards. The KTM 1190 skid plates pivots toward the rear of the bike enabling easy access to the drain plugs, battery, and fuel pump. Installation is an easy bolt on procedure using the existing mounting locations, stock bolts and rubber pivot bushings. Durable material, quality construction, unique design, easy installation and reasonable price all add up to a great value. Mounts easily and quickly using the existing mounting locations, stock hardware and rubber pivot bushings. Designed to cover the exposed lower portion of the engine and it's critical components. Integrated protection for the engine center cases, clutch cover, ignition cover, side stand switch, side stand mount, battery and fuel pump. Easy access to the battery, fuel pump, and engine oil drain plugs by utilizing the pivot/tilting design. Unlike painted/powder coated skid plates that become less attractive over time due to chips and scratches, the brushed aluminum finish of the Slavens 950/990 skid retains it's classic good looks. Excellent quality for a fair price. Easy to install in less than 5 minutes. Available in brushed aluminum & black anodize. Made in the U.S.A.
Plastic Skid Plates for KTM, Husaberg, Husqvarna by TM Designworks
$94.95
– $99.95
Every purchase includes instructions, diagrams, & the necessary special hardware to install the plate. These plates do not include oil drain hole to guarantee maximum protection. Easy to follow instructions and template to put a drain hole in the skid plate are included. Currently available in black for KTMs and Husabergs. Protects the main frame rails, ignition, clutch, & water pump cases; Is not a lower strength, injected molded part like Acerbis, Cycra, or Hyde; All new, patented forming technique mirrors frame bends for a perfect fit without stress or potential cracks; Proprietary mix of nylon, Kevlar® & silicone; 35-40% lighter than most aluminum skid plates; Virtually impact resistant; Strong, secure 3 point (front, middle, and rear) mounting; Easy to install, lightweight and strong; Reduces engine sound; Includes instructions & mounting hardware; Made in the USA; Available in orange or black.
Skid Plates Honda
$87.95
These Honda Skid Plates are extremely rugged, made of durable 3/16 7075 T-6 aluminum, are designed for maximum protection and ease of maintenance. Durable material, quality construction, oil drain access, easy installation, and reasonable price make it a great value.
Skid Plates Kawasaki KLX450R
$87.95
Kawasaki Skid Plates are extremely rugged skid plates, made of durable 3/16 7075 T-6 aluminum, are designed for maximum protection and ease of maintenance. Durable material, quality construction, oil drain access, easy installation, and reasonable price make it a great value.
Skid Plates Yamaha WR250/450F
$87.95
These Yamaha Skid Plates are extremely rugged, made of durable 3/16 7075 T-6 aluminum, are designed for maximum protection and ease of maintenance. Durable material, quality construction, oil drain access, easy installation, and reasonable price make it a great value.
Skid Plates for Husaberg by Flatland
$89.95
Husaberg Skid Plates by Flatland Racing are made of rugged 3/16 7075 T-6 tempered aluminum and feature TIG welded engine guards. Flatland Racing skid plates also offer a built in clean out slot and oil drain hole, along with a hole for oil screen removal where applicable. The Husaberg 4 stroke skid plates enable easy access to the drain plugs and screens. Installation is an easy bolt on procedure with all mounting hardware included. Durable material, quality construction, unique design, easy installation, and reasonable price make it a great value. Constructed of rugged 3/16 (5mm) 7075 T-6 tempered aluminum; TIG welded; Oil drain hole; Easy access to drain plugs and screens; Easy installation; Quality construction; Mounting hardware included; Made in the U.S.A.
Skid Plates for KTM 690 Enduro,950,990 Adventure
$89.95
– $244.00
Slavens KTM Skid Plates are made of rugged 5mm thick 5052 aluminum and feature TIG welded engine guards. The KTM 950/990 skid plates pivots toward the rear of the bike enabling easy access to the drain plugs, battery, and fuel pump. Installation is an easy bolt on procedure using the existing mounting locations, stock bolts and rubber pivot bushings. Durable material, quality construction, unique design, easy installation and reasonable price all add up to a great value. Mounts easily and quickly using the existing mounting locations, stock hardware and rubber pivot bushings. Designed to cover the exposed lower portion of the engine and it's critical components. Integrated protection for the engine center cases, clutch cover, ignition cover, side stand switch, side stand mount, battery and fuel pump. Easy access to the battery, fuel pump, and engine oil drain plugs by utilizing the pivot/tilting design. Unlike painted/powder coated skid plates that become less attractive over time due to chips and scratches, the brushed aluminum finish of the Slavens 950/990 skid retains it's classic good looks. Excellent quality for a fair price; Compatible with ALL sidestand relocation kits & the stock centerstand; Easy to install in less than 5 minutes; Available in brushed aluminum, anodized black, anodized orange; Made in the U.S.A.
Skid Plates for KTM by Flatland Racing
$89.95
– $249.95
KTM Skid Plates by Flatland Racing are made of rugged 3/16 7075 T-6 tempered aluminum and feature TIG welded engine guards. Flatland Racing skid plates also offer a built in clean out slot and oil drain hole, along with a hole for oil screen removal where applicable. The KTM 4 stroke skid plates pivot forward, enabling easy access to the drain plugs and screens. Installation is an easy bolt on procedure with all mounting hardware included. Durable material, quality construction, unique design, easy installation, and reasonable price make it a great value.
Swingarm Guards
Bullet Proof Designs KTM/Husaberg Swingarm Guard
$48.95
– $72.95
Machined from a solid block of 6061-T6 aluminum for superior strength; Guard protects and supports chain guide and swingarm mounting tabs; A must have for rocky trails; Comes complete with all hardware, drill and tap; Lifetime guarantee; Fits the stock guide, TM Designs, Hard Parts SXS guide, and BRP guide.
Gen 2 Swingarm Guard for KTM, Husaberg, Husqvarna by Bullet Proof
$74.00
– $79.00
The new Gen 2 Swingarm Guard by Bullet Proof Designs gives ultimate protection from rocks, logs, tree stumps and other trail trash. This is a must have item for all types of riding, from casual trail riding to crazy extreme enduros. Used and endorsed by KTM, Husaberg, Husqvarna factory team riders Taddy Blazuziak, Steward Baylor and Mike Lafferty. Designed and developed by machining wizard Bad Bud Carmen. When you want the absolute best, buy Bullet Proof!!! Machined from billet 6061-T6 aluminum for superior strength and light weight; Only weighs 3oz; Guard protects and supports swingarm chain guide mounting tabs; A must have for rocky, log infested trails; Comes complete with all hardware, drill and tap; Lifetime guarantee; Fits the stock chain guide, TM Designs, Hard Parts SXS guide, and BRP guide; Made in the USA by guys who ride.
Hardware
50 Piece Fastener Kit for KTM/Husaberg/Husqvarna by EE
Euro Style Pro-Pack 145 Piece Kit for KTM, Husaberg, Husqvarna by Bolt
$56.95
Only aftermarket company to offer hardware in KTM, Husaberg, '14 Husqvarna factory style and finish; Includes over 145 pieces of M6 and M8 dimpled flange bolts, concave washers, carb screws, shroud screws, sprocket bolts, Brembo style brake pin clips, and more. Includes 3 sizes of factory style aluminum bushings, aluminum rim-lock spacers, drain plug washers, sub-frame bolts, M5 dimpled flange bolts and valve stem grommets; Fits all full size late model KTM, Husaberg, '14 Husqvarna off road motorcycles.
Full Plastic Fastener Kit for KTM by Bolt
$19.95
Includes all factory replica fasteners and aluminum bushings needed to fasten complete bodywork; OEM quality fasteners at a fraction of the cost; A must when installing new plastic on your bike.
Hub Saver Sprocket Bolt Kit for KTM, Husaberg, Husqvarna by Bolt
$10.95
This sprocket bolt kit includes (6) class 10.9 silver zinc plated carbon steel sprocket bolts with (6) factory style mechanical-locking "Fuji" nuts. Each sprocket bolt has medium strength threadlock patch applied for a double-lock. Threadlock liquefies and anaerobically seals when the bolt is tightened. Features 12mm Fuji nuts with 8mm hex head bolts which are far less likely to round or strip out during installation. These are the strongest yet lightest bolts available on the market. These are universal bolts which we recommend to use with our rear sprockets for nearly all bike makes/models. Includes 6 bolts & 6 nuts; Threadlock patch on each bolt; Available in silver or black.
Rotor Bolt Kit for KTM, Husaberg, Husqvarna by Bolt
$9.95
Be sure your dirt bike is in safe working order and the rotor stays tight on your KTM/Husaberg/Husqvarna with quality rotor bolts. This kit features medium strength threadlock pre-applied to the rotor bolts. Bolt Motorcycle Hardware meets or exceeds OEM hardware and is made out of quality materials in the USA. (12) M6x13mm rotor bolts; O.E.M. style; Includes bolts for front and rear rotor installation; Includes pre-applied medium threadlock; Made in the U.S.A.
Lift Straps & Handles
Grab Handle for KTM by Enduro Engineering
$36.99
The all new Enduro Engineering grab handle has been designed to create a stable lifting point on '11 (limited models) & '12-'13 125-500 KTMs. Machined from billet aluminum; Black anodized; Quick and easy to install; Includes all mounting hardware; Made in the USA.
Pro Tows Tow Straps by MSR
$14.95
No matter how great of a rider you are or how well maintained you bike might be, at some point you will likely need a tow. These straps are built just for that occasion. 15 ft. long; White labeling area for easy personalizing; 1 (22mm) wide nylon webbing rated at 1,500lbs; Carrying pouch and user instructions included.
The Tugger Lift Strap
$13.95
– $29.99
The Tugger Lift Strap provides a convenient gripping point near the front or rear of your dirt bike. Most dirt bikes don't have a place to grab that won't toast your fingers or get your gloves muddy. The Tugger is ready when you need it and stays out of the way when you don't. Perfect on the trail when you need to maneuver your bike over a rock, around a tight switchback or get it out of a deep rut. No more burning your hand on your hot silencer, getting your gloves covered in mud from grabbing the rear fender or breaking the fenders because you used them as a handle. Easy to install, lightweight, tough, and convenient. The front Tugger mounts to the front forks, providing a handy place to grab when you get in those situations where someone else is pulling on your bike. And for adults riding with your child, the front Tugger is especially handy for helping your child through nasty situations. Quick and easy to install; Lightweight; Tough; Convenient; Front Tugger fits ALL dirt bikes; Rear Tugger fits many brands.
Seats
Covers & accessories
Comfort Seat Foam and Cover for KTM 125-530 by Seat Concepts
$159.95
Seat Concepts seat cover and foam kits have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat cover/foam kit was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat kit. The seat cover and foam kits are "Do It Yourself" with detailed instructions for easy installation. Comfort seat foam; Orange stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Easy installation ("How to" video); Made in the U.S.A.
Gripper Seat Covers for KTM by Flu Designs
$29.99
The new FLU Designs Gripper Seat Cover is a specifically designed seat cover to enhance your ability to maintain proper rider position. Flu has put in a lot of time at the test track and at the races with some of the top factory pro riders to design a seat cover that offers maximum traction but still lets you slide around on the seat when needed. The grip top will help to keep you in place when you are hard on the throttle or trying to seat bounce a difficult jump out of a turn. While under braking though you will still be able to slide forward on the seat so you can weight the front of the bike for that much needed traction in the turns. The Gripper seat cover also features grip material on the side panels of the seat for that much needed traction while standing and griping the bike with your knees. This type of seat technology has only been available to top factory pros but is now available to you. Available for most current KTMs. Made of high-quality, one-piece medium grip material; Features extra material to fit tall or standard seat foam; Helps maintain proper rider position; Offers maximum traction; Used by Team KTM; Easy to install.
Pleated Gripper Seat Covers for KTM by Flu Designs
$46.95
The new FLU Designs Pleated Gripper Seat Cover is a specifically designed seat cover to enhance your ability to maintain proper rider position. Flu has put in a lot of time at the test track and at the races with some of the top factory pro riders to design a seat cover that offers maximum traction but still lets you slide around on the seat when needed. The pleated ribbed designed grip top will help to keep you in place when you are hard on the throttle or trying to seat bounce a difficult jump out of a turn. While under braking though you will still be able to slide forward on the seat so you can weight the front of the bike for that much needed traction in the turns. The Pleated seat cover also features grip material on the side panels of the seat for that much needed traction while standing and gripping the bike with your knees. This type of seat technology has only been available to top factory pros but is now available to you. Available for most current KTMs and Husabergs. Made of high-quality, one-piece medium grip material; Features extra material to fit tall or standard seat foam; Helps maintain proper rider position; Offers maximum traction; Used by Team KTM; Easy to install.
Seat Cell Phone Pocket by EE
$39.95
Need a convenient place to carry your cell phone, money, drivers license? This handy pocket has a clear top to be able to see if your phone is ringing and easily attaches to most any motorcycle seats by just wrapping the strap around the back of your seat and attaching the Velcro. Holds cell phones, iPods, wallets, etc.; Quick and easy to install; Made in the USA.
Enduro Engineering
Comfort Seat for KTM, Husaberg by Enduro Engineering
$119.95
The EE KTM, Husaberg Comfort Seats offer softer, more comfortable foam with an improved seat base design that increases flow to the air box and air filter. Tired of monkey butt? It offers all day riding comfort with a redesigned seat pan that allows for an additional 1.50 inches of foam without changing the seat height. This is a complete seat, designed and manufactured in the USA. Available in tall (additional 1.25") or standard height with soft or firm foam.
Husaberg Pure Tech
Low Gel Seat for Husaberg by Pure Tech
$132.00
The Husaberg low gel seat by Pure Tech offers a softer, more comfortable gel & foam combo with a correct fit seat base. This complete seat is 15mm (.60) shorter than the stock seat. Provides shorter riders with optimum control of the motorcycle in difficult terrain. Pure Tech quality; Complete seat; 15 mm (.60) lower than the standard seat; Correct fit.
Tall Gel Seat for Husaberg by Pure Tech
$132.00
The Husaberg tall gel seat by Pure Tech offers a softer, more comfortable gel & foam combo with a correct fit seat base. This complete seat is 20mm (3/4) taller than the stock seat. Pure Tech quality; Complete seat; 20mm (3/4) taller than stock; Correct fit.
KTM Powerparts
Low Gel Seat for KTM by KTM Powerparts
$124.95
The KTM Powerparts low gel seat offers a softer, more comfortable gel & foam combo with a correct fit seat base. This complete seat is 15mm (.60) shorter than the stock seat. Provides shorter riders with optimum control of the motorcycle in difficult terrain. KTM Powerparts; Complete seat; 15 mm (.60) lower than the standard seat; Correct fit.
Step Seat for KTM by KTM Powerparts
$124.95
The KTM Powerparts step seat limits the rider from slipping backwards during hard acceleration. This is a complete seat with a correct fit. Provides shorter riders with optimum control of the motorcycle in difficult terrain or on the track. KTM Powerparts; Complete seat; No slipping backwards during acceleration; Correct fit.
Tall Gel Seat for KTM by KTM Powerparts
$124.95
The KTM Powerparts tall gel seat offers a softer, more comfortable gel & foam combo with a correct fit seat base. This complete seat is 20mm (3/4) taller than the stock seat. KTM Powerparts; Complete seat; 20mm (3/4) taller than stock; Correct fit.
Seat Concepts
Comfort Seat Cover & Foam Kit for KTM LC4 620,640,690 by Seat Concepts
$169.95
Seat Concepts seat cover & foam kits have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat kit was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat. These are cover and foam kits, not complete seats. Comfort seat foam; Orange stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Made in the U.S.A.
Comfort Seat Cover & Foam Kit for KTM LC8 950,990 by Seat Concepts
$169.95
Seat Concepts seat cover & foam kits have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat. These are seat cover & foam kits, not complete seats. Comfort seat foam; Orange stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Made in the U.S.A.
Comfort Seat Cover & Foam Kits for 2013 Husaberg TE/FE by Seat Concepts
$159.95
Seat Concepts seat cover and foam kits have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat kit was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat. These are seat cover & foam kits, not complete seats. Comfort seat foam; Blue stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Available in low, standard, and tall height; Made in the U.S.A.
Comfort Seat Foam and Cover for KTM 125-530 by Seat Concepts
$159.95
Seat Concepts seat cover and foam kits have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat cover/foam kit was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat kit. The seat cover and foam kits are "Do It Yourself" with detailed instructions for easy installation. Comfort seat foam; Orange stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Easy installation ("How to" video); Made in the U.S.A.
Comfort Seat for KTM 125-530 by Seat Concepts
$249.95
Seat Concepts Complete Comfort Seats have a wider seating area towards the rear of the seat for greatly increased comfort on long rides. This improved shape helps spread the load to alleviate pressure points. Each seat was designed to increase comfort with out compromising your ability to ride aggressively. The more aggressive the bike, the more aggressive the seat. These are complete seats, not kits. Comfort seat foam; Orange stitching for custom look; Gripper top material; Carbon fiber look side material; Wider seating area for increased comfort; Slim profile above footpegs; Comfortable for long rides; Improved foam density and composition; Made in the U.S.A.
TUbliss (tube replacement)
TUbliss Replacement Parts by Nuetech
$1.95
– $35.00
Purchase extra or replacement liners (the red piece) or inner bladders for the Nuetech TUbliss Core in 18, 19 and 21 sizes. We stock a full selection of all replacement parts for the TUbliss system.
TUbliss Tubeless Core Tire System by Nuetech
$84.90
Gen 2.1 TUbliss Core Tire System by Nuetech: It's not about going tubeless for the sake of eliminating tubes. It's all about the countless benefits of going TUbliss that makes every rider and racer better, faster, and more in control. The Gen 2.1 Nuetech TUbliss®: tire core system is essentially a high pressure rim lock and seal that secures the entire tire bead to the rim, completely eliminating the use of a conventional tube. It allows you to run a low tire pressure (as low as 6 psi) which dramatically improves traction; especially important for off-road riding and racing. Since there's no conventional tube the days of pinched tubes and flats are over! Even if you get a tire puncture the bead stays seated to the rim. The 120 psi inner bladder literally clamps the entire bead and side wall of the tire to the rim, providing full bead lock performance around the full circumference of the rim. The seal is formed against the inside of the tire itself, not the rim, so it holds the tire firmly and makes the sidewalls stay upright and absorb the full impact, unlike bending and deflection you get with conventional tubes. Because of the design, the Nuetech TUbliss® tire core system will even work with the most dented, dinged, or tweaked rim.
This re-sealable tub comes with a filter tray that allows dirt to sink to the bottom, away from your filter. Filter cleaner sold separately. Re-sealable; Filter tray included; Cleaner sold separately.
Foam Filter Oil by Belray
$13.49
Bel-Rays Foam Filter Oil formula will ensure full engine protection and performance. Superior tackiness traps air filter dust, dirt and even water. Waterproof formula won't wash out, gum or clog. Dark blue color makes it easy to see when filter is thoroughly covered and dries quickly so you'll be up and running sooner. Designed to improve air flow; Traps microscopic particles to extend engine life; Waterproof formula prevents clogging when wet; For foam air filters only.
Oiling Tub by Twin Air
$10.95
Submerge your clean filter in this tub for easy, even oiling. Then massage out the excess oil and reseal to store your unused filter oil. Filter oil sold separately. Quick and easy filter oiling; Holds filter oil for future use; Filter oil sold separately.
Oils & Cleaners by Twin Air
$13.95
– $94.95
Original: The original formula sets the standard of excellence in filter oils; Starts thin for even distribution then turns super tacky to trap dirt, grit, and dust; Dirt remover removes all oil for easy clean-up. Bio: Bio oils and cleaners are formulated for superior performance and to be friendly to our environment; Easy clean-up in your washing machine or sink.
Brake Fluid
RBF 600 Racing Factory Line Brake Fluid by Motul
$21.95
For all types of hydraulic brake and clutch actuators requiring non-silicone synthetic fluid. Specially designed to resist the extreme temperatures generated by carbon and ceramic racing brakes with minimum brake cooling. 100% Synthetic Racing Fluid - DOT 4; Very high boiling point: 594°F / 312°C; Widely exceeds DOT 3, DOT 4 and DOT 5.1 standards; Ultra efficient in the rain: Very high wet boiling point 421°F / 216°C.
RBF660 Pro Racing Brake Fluid by Motul
$29.95
For all types of hydraulic brake and clutch actuators requiring non-silicone synthetic fluid. Specially designed to resist the extreme temperatures generated by carbon and ceramic racing brakes with minimum brake cooling. 100% Synthetic Racing Fluid - DOT 4; Very high boiling point: 617°F / 325°C; Widely exceeds DOT 3, DOT 4 and DOT 5.1 standards; Ultra efficient in the rain: Very high wet boiling point 400°F / 204°C.
Cleaners
Clean Up Chain Cleaner by Maxima Racing Oils
$9.95
Excellent chain cleaner and degreaser; Removes caking and build-up on chain and sprockets; Won't harm sealed or non-sealed chain Easily washes off with water; 15.5 fl oz aerosol.
Multi Purpose Penetrating Lube by Maxima Racing Oils
$9.50
Multi purpose penetrating lube; Excellent fogging oil; Displaces moisture to inhibit rust; Frees corroded parts; 14.5 fl oz aerosol.
Suspension Clean by Maxima Racing Oils
$8.95
Quickly removes suspension fluid and grease; Professional formula is fast drying - leaves no residue; Displaces moisture; Will not harm O-rings or seals; Specifically formulated for the powersports industry; 13 fl. oz. aerosol.
Coolant
Coolant by Engine Ice
$21.95
Engine Ice Hi-Performance Coolant offers superior performance in all types of water-cooled engines. Extensively tested in extreme heat and humidity in race conditions. Made of Propylene Glycol which is biodegradable and non-toxic; Premixed with de-ionized water which eliminates all impurities - even distilled water contains particles of metal and chemicals which cause scarring, scaling, clogging and mineral buildup; Proven to reduce operating temperatures by as much as 50 degrees F - a necessity for today's high-performance bikes which overheat just idling; Engine Ice is the only coolant sold in motorcycle dealerships that is legal in AMA, CCS, FUSA Road Racing and AMA/Prostar Drag Racing; Used by top racers like James Stewart, Ernesto Fonseca, Chad Reed, Randy Hawkins and many more.
Powersports Coolant by Evans
$28.95
Evans Powersports Coolant offers improved performance and reliability. Even under extreme conditions, Evans Powersports Coolant will not overheat and using it allows the engine to be safely tuned for more power. A higher compression ratio, leaner mixture, and more advanced spark are some of the options available to the engine builder. It provides permanent cooling protection for the life of the engine so replacement is never necessary. Its superior corrosion protection is not degraded over time and it won't freeze or damage engine components. Proven to eliminate all problems associated with water based coolant; Redefines the boundaries of engine cooling; Improves your cooling system performance; Does not boil over or freeze; Non-toxic to humans and animals; Protects your engine, extending it's life and improving reliabilty; Performs for the life of the engine without the need to refresh; Won't freeze or damage engine components; Superior corrosion protection; 64oz. container.
Fluids & Lubricants
Maxum 4 Blend Oil by Maxima Racing Oils
$10.95
– $129.95
Maxima's Maxum 4 Synthetic Blend is a blend of ester-based synthetic and petroleum base stocks featuring advanced technology. This special high temperature formula protects critical engine components, reduces wear, friction, temperature, oil consumption and extends drain intervals. The use of new anti-shear additives assures viscosity stability for motorcycle 4-cycle engines with integrated transmissions. This formula also has extra anti-scuff additives to handle extreme loads and peak temperatures. Maxum 4 synthetic blend is a blend of ester-based synthetic and petroleum-based stocks; Special high temperature formula protects critical engine components; Exceeds SPI SG/CC specs; Motorcycle specific JASO-MA; 10W40 and 20W50; 1 liter and 1 gallon available; 1 liter case = 12 bottles; 1 gallon case = 4 bottles.
Maxum 4 Break-In Oil by Maxima Racing Oils
$8.95
– $91.29
Specifically designed for breaking in engines; Advanced technology for optimum ring seal; 2X Zinc formula; Unsurpassed protection during engine break-in; Fully formulated 10W30; 1 liter bottle; Case = 12 bottles.
MTL Motorcycle Transmission Fluid by Maxima
$9.95
MTL has been significantly improved with new technologically advanced additive systems that drastically improve clutch life and reduce slippage. While accomplishing this, MTL provides outstanding anti-wear protection and lubrication to the transmission as well. This new formula has been extensively tested on the race track by many of the nations top mx teams and tuners and is now available to the serious competitor. Reduces clutch slippage; Reduces clutch wear; Protects transmission gears; Protects against all mechanical wear; Anti-foam formula; For all air and water-cooled 2-cycle and 4-cycle transmissions with wet clutch systems; 80 weight; We recommend MTL 80wt for ALL KTM & Husaberg 2 strokes.
Multi Purpose Penetrating Lube by Maxima Racing Oils
$9.50
Multi purpose penetrating lube; Excellent fogging oil; Displaces moisture to inhibit rust; Frees corroded parts; 14.5 fl oz aerosol.
Offroad Chain Lube by Motul
$9.49
Is highly recommended for motocross and off-road use; Light tack so not to attract dirt and sand; Protects chains from grease and dust build-up; Suitable for all chains with or without O-ring seals; Net 13.5oz/Fluid 9.2oz.
Saber 2 Stroke Premix by Amsoil
$2.95
– $4.99
Saber Professional Synthetic 100:1 Pre-Mix 2-Cycle Oil (ATP). AMSOIL Saber Professional is formulated with exclusive AMSOIL synthetic base oils and premium additives. Designed for lean mix ratios in two-cycle motors, Saber 2-Cycle Oils have excellent lubricity and cleanliness properties to control friction and help prevent wear, plug fouling, ring sticking and exhaust port blocking. Saber 2-Cycle Oils also feature an anti-rust formulation to counteract the damp environments often encountered in two-cycle applications. AMSOIL 100:1 Synthetic 2-Cycle Oils have been protecting and providing improved performance in two-cycle motors since 1973.
Silicone Lubricant for Bib Mousse & Tire Balls
$21.95
– $36.95
This 100% silicone oil reduces friction inside the tire when using tube replacement products such as Tire Balls or Bib Mousse. 100% silicone oil; Reduces friction; Recommended for Bib Mousse and Tire Ball installation.
Transoil Expert Gearbox Oil by Motul
$11.50
Semi-synthetic 10w40; Smother shifting; Anti-wear, anti-corrosion and anti-foam capabilities; Formulated for 2 & 4 stroke gear boxes with wet clutch; Fortified with extreme pressure additives for gear protection; Standards: API GL4; Recommended by Rekluse for auto-clutches.
Sealants
Liquid Gasket Semi-Dry 1184 by ThreeBond
$11.95
Excellent padding properties make this semi-drying sealer perfect for joint surfaces with large clearance. The synthetic rubber absorbs vibrations and impacts without failure, especially when coolants are involved. Seals joint surfaces to prevent leakage of oil, water, coolants or chemicals; Recommended for sealing KTM/Husaberg/Husqvarna 250/300 cylinder front cover; Similar to YamaBond 4; O.E.M. approved; 3.5oz.
QuickSteel Epoxe Putty
$6.49
Dries steel-hard in 15 minutes; Ready to drill and tap in 1 hour; Easy to use - no waste; 500 degree temperature resistant; 3 year shelf life; Sets up under water; Impervious to chemicals; Permanently bonds to aluminum, brass, copper, steel, plastics & much more.
Tire Balancer & Sealant by Ride-On
$14.95
– $19.95
Ride-On Tire Protection System tire sealant for motorcycles has been designed for use in high speed applications without causing vibrations. Ride-On TPS tire sealant for motorcycles helps improve the tire balance, seals punctures from objects up to 1/4 (1/8 for tubes) in diameter, prevents flats and helps tires last longer. Ride-On TPS tire sealant for motorcycles contains corrosion inhibitors that protect aluminum and steel wheels against rust. Ride-On also helps reduce dry rot and eliminate the tiny, invisible porosity leaks that cause tires to deflate over time. Ride-On TPS for motorcycles saves you money by increasing tire life, reducing down time, and lowering road service calls. Ride-On TPS (Tire Protection System); Tire balancer and sealant compound that evenly coats the inner surface of tires; This coating balances tires and makes them into self-sealing tires while you ride; Eliminates need for those ugly wheel weights; Hydro dynamically balance high-speed tires, dampen road noise and vibrations that cause a rough ride; Centrifugal force of the tire and the internal air pressure force Ride-On into a hole sealing it instantly; Seals up to 1/4 in tubeless and 1/8 in tube tires; Ride-On is a green biodegradable product that is designed to be non-hazardous and non-flammable; Corrosion inhibitors protect all alloys of steel, aluminum, magnesium and yellow metals against oxidation; Most motorcycles require 2-3 8 oz. bottles per bike.
Tire Sealant by Slime
$7.45
– $10.45
As the Slime treated tube/tire rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes/tires losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is NOT recommended for use in tubeless tires. Prevents and repairs punctures up to1/8 (3mm) using Fibro-Seal technology; Remains liquid inside the tire, coating the tread area as the tire rotates; Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble; Tubes treated with Slime can be patched with a conventional vulcanized patch using a bit of patience and care!
Suspension Fluids
Racing Fork Fluid by Maxima
$12.95
Maxima Racing Fork Fluid is designed to drastically reduce stiction and meet all front suspension needs on both standard & cartridge systems. This advanced formulation utilizes the latest friction reducers, anti-foam, rust & corrosion inhibitors and is resistant to oxidation & viscosity changes. This viscosity index over 190+ assures constant fork action over a wide temperature range and also contains seal conditioners and shear stable polymers for long life. Racing fork fluid 5wt is the same viscosity fluid as 01, SS7, or std. KYB fluid and is recommended for most late model mx forks and ALL KTM and Husaberg WP forks. Zero drag anti-frictional formula; Contains rust and corrosion inhibitors; Anti-foam and oxidation stabilizers; May be used in standard or cartridge forks - ALL brands; Used and recommended by Slavens Racing.
Racing Shock Fluid by Motorex
$84.95
Shock absorber oil for racing with a high viscosity index. Provides optimum damping even under extreme conditions. Prevents the formation of foam and inhibits corrosion. Developed with WP Suspension Company; Race tested and proven performance; Recommended and used by Team KTM; Used by Slavens Racing; Only available in 5 liter jug; For use in WP, Showa, KYB, Ohlins, Sachs, Fox, RT shocks.
Synthetic Racing Fork Fluid by Silkolene
$27.95
Unique synthetic fluids, integrated with Electrosyntec Technology and race-developed foam and wear-resistant chemistry, to give exceptional performance in the latest front forks and suspension systems. Offers outstanding resistance to shear forces and high temperatures. Ideally suited to long distance events and severe conditions where consistent performance, from start to finish, is vital. Reduces friction and 'stick-slip' to give smooth action. Used extensively by factory teams and suspension specialists in off road and road racing competition.
Controls
Cables & lines
Black Vinyl 2 Stroke Throttle Cables for KTM, Husaberg, Husqvarna by Motion Pro
$13.95
– $14.95
Motion Pro Black Vinyl 2 Stroke Throttle Cables are an economical solution to old sticky, worn, or broken throttle cables. A definite upgrade over stock with a inner nylon sleeve for longer life and smoother operation. Black vinyl coil-wound housing; Meets or exceeds OEM quality; Inner nylon sleeve for longer life and smooth operation; Available in standard length and +4" (+102mm) for alternate routing.
Black Vinyl 4 Stroke Push-Pull Cable Sets for KTM by Motion Pro
$37.95
– $48.95
Motion Pro Black Vinyl 4 Stroke Push-Pull Cable Sets are an economical solution to old sticky, worn, or broken throttle cables. A definite upgrade over stock with a inner nylon sleeve for longer life and smoother operation. Black vinyl coil-wound housing; Meets or exceeds OEM quality; Inner nylon sleeve for longer life and smooth operation; Available in standard length and +3" (+76mm) for alternate routing.
Brake Line/Hose Kits for KTM, Husaberg, Husqvarna by Galfer
$52.95
– $69.95
Galfer has been leading the motorcycle industry by consistently making performance products that withstand the rigors and abuse of motocross racing and aggressive riding. Galfer's off road brake lines feature a heavy-duty stiffener sleeve over the hose to route just like the O.E.M. units. Kits come complete with banjo bolts and washers. Withstands the rigors and abuse of motocross racing and aggressive riding; Constructed from stainless steel to avoid flexing for maximum stopping power; Complete with line, fittings, banjo bolts, and crush washers for complete and easy installation; Stainless steel brake lines allow maximum feel while reducing overall braking effort; Will out-perform stock brake lines; Lifetime warranty; Pre-positioned banjos for easy installation, although adjustable as needed; Made in the USA.
Clutch Line/Hose Kit for KTM, Husaberg, Gas Gas, Husqvarna
$53.95
This durable braided stainless steel hose will ensure solid clutch pressure every time. Also features an elbow fitting at the master cylinder to route around handguards. All necessary hardware is included. Durable stainless steel braided cover; Positive clutch pressure; Elbow fitting for routing around handguards; Includes banjo bolts and crush washers; Made in the U.S.A.
T3 Slidelight Throttle Cables for KTM, Husaberg, Husqvarna by Motion Pro
$35.95
– $36.95
The Motion Pro T3 is a premium grade throttle cable designed for safety and longevity. If snagged by a bush or branch the stock cable will pull loose from the carburetor and a wild, uncontrolled ride will ensue. The T3 has a unique crimpless design that holds the cable housing securely in place yet enables easy installation and adjustment. It's available in standard length and +5 (+127mm) for alternate routing. Premium throttle cable designed for 2-stroke motorcycles; Adjuster barrel is attached to the cable housing with a unique crimpless pivot fitting which holds housing securely in place and cannot pull out of adjuster like OEM cable; Features oversize 6 mm black vinyl housing with smooth PE liner and a 1.5 mm ultra flexible stainless steel inner wire; Pivot fitting allows adjuster barrel to turn freely for easy installation and adjustment; 6 point billet aluminum adjuster nut with lightening holes with durable titanium gray anodized finish provides a factory works bike look; Available in standard length and +5" (+127mm); Hand made in the USA by Motion Pro.
Grips
Dual Compound Kevlar Grips by Renthal
$19.95
The most advanced grip available. Renthal has developed a special reinforced grip made with increased wear resistance. The grip has all the properties you would expect from a Renthal grip but with the life extending properties of KEVLAR brand resin. KEVLAR reinforced grip; The base material is reinforced with millions of randomly aligned KEVLAR fibers. As the grip is used, more Kevlar fibers are exposed; This KEVLAR layer offers three times the life of the regular compound which allows us to use a very supple matrix material; This revolutionary material lasts three times as long as our regular soft material; For use with twist throttles; If you use glue on the installation of Renthal grips, due to the specific compound, only Renthal grip glue will work.
Grip Glue by Renthal
$7.95
Renthal applied their years of motorcycle championship winning experience to develop grip glue that holds strong and is easy to use. Features: Renthal Grip Glue is highly developed grip glue that is specially formulated to hold your motorcycle or ATV grip strongly without damaging the grip; Renthal grip glue prevents the grip from slipping and squirming during aggressive riding and racing conditions; A must when using soft or medium compound grips.
Heat Demon Grip Heaters/Hand Warmers by Symtec
$56.95
The Symtec Heat Demon Heated Grips are a great, must have accessory. 2-stage heated grips that keep you comfortable and warm and riding with these really do extend your riding season. This quality kit allows the heating elements to be fitted neatly and discretely under the O.E.M. grips or your own favorite aftermarket grips. Easy to install, with 2-stage heat settings, the kit is suitable for all types of bikes, tourers, sports, and off road/enduro bikes. The kit consists of two heating elements on flexible Mylar tape that attaches to your handlebar (clutch side) and throttle tube (throttle side) via permanent adhesive on the back. The right and left heaters are different, to accommodate lower heat tolerance of plastic throttle tubes.
M1 MX/Offroad Grips by Spider
$16.95
Spider Grips use a dual layer manufacturing technique to offer superior comfort and durability over single layer grips. The inner layer includes the flange and the end cap which is specially designed to resist punching out. The outer layer features a soft density diamond pattern designed to shed water and mud while having a tacky surface for maximum grip. Spider Grips also feature ART (Acoustical Rebound Technology) a patent pending design that refers to the special shaping of the boundary layer that deflects vibrations away from the rider. Features: Dual layers of Spider Traction Gel engineered to rebound and absorb more vibration than any other grip on the market, while shedding mud and water to make it easier to hold on to; Full flange and a super strong end cap ideal for off-road, dual-sport and motard riding.
Pillow Top Grips by Pro Taper
$12.95
3-D (Tri-Density) Technology - Try the grip with the technical advantage of three dedicated rubber compounds. Vibrasonix pillow top eliminates vibration and cushions impact; Tacky gel-like surface compound is perfect for off-road riders; Inner core compound perfects the bonding interface with bars; ANTI-Rip Tip uses denser compound to increase life of the grip; Designed to self-clean and shed mud away from outer surface.
Pillow Top Lite Grips by Pro Taper
$12.95
3-D (Tri-Density) Technology - Try the grip with the technical advantage of three dedicated rubber compounds. Lower profile for better overall hand control; Vibrasonix pillow top eliminates vibration and cushions impact; Tacky gel-like surface compound is perfect for off-road riders; Inner core compound perfects the bonding interface with bars; ANTI-Rip Tip uses denser compound to increase life of the grip; Designed to self-clean and shed mud away from outer surface.
Handlebars
Anti-Vibration Inserts by Fasstco
$59.95
A Discreet yet incredibly effective component to any serious racer or casual rider, Fasstco anti-vibration inserts do a great job of absorbing vibration transferred from the bars to your hand, yielding less fatigue and arm pump. Riderss have been installing them in anything with handlebars, from quads to superbikes, with great results. Constructed out of brass with an elastomer expansion joint mounted inside of the handlebars. The Anti-Vibration Bar Insert Kit comes with different end caps to accommodate most handguard systems plus end-caps for use without handguards. Quick and easy install; CNC machined from bras; Incredibly effective; Less hand fatigue and arm pump; Used by factory teams; Fits most aluminum handlebars; Great for dirt, dual-sport, street, road-racing; Made in the U.S.A.
Billet Throttle Tube for KTM, Husaberg, Gas Gas by G2 Ergo
$59.95
The G2 Throttle Tube consists of the ultra-smooth G2 tube with Delrin inserts fitted with a 100 throttle cam that is the same size as stock. The throttle tube shares the unique G2 cam and tube interlock that allows the rider to update to a quicker turn or control cam, sold separately, at any time. Burley replacement for wimpy plastic/nylon tubes; Includes throttle tube with stock size cam; Machined from 6061 aluminum; Self-lubricating Delrin bushings at each end of tube provide an ultra-smooth feel; Included cam is removable and can be replaced with alternate cams (sold separately) to fine tune control; Fits inside the stock throttle housing to stock cables; Removable end cap for simple handguard installation; Installs in minutes; Made in the U.S.A.
BRP Hand Guard Mounts
$69.95
BRP Hand Guard Mounts are a perfect hand guard mounting solution when space is limited or when controls interfere with standard hand guard mounts. Also a great option for Scotts sub mounted damper applications applications. Made from aircraft quality aluminum and black anodized for a trick look. BRP Hand Guard Mounts have the same contour and shape as BRP & Scotts SUB Mounts. Fits all 39 - 41mm spacing - over-sized 1 1/8 handle bar mounts. KTM, Husabergs, etc.) Kit includes all necessary hardware: Perfect solution when space is limited or controls/cables/hoses interfere; CNC machined from strong aircraft quality aluminum billet Black anodized; Same shape and contour as BRP & Scott triple clamps; Works well with Scotts Sub mount damper kits; Fits stock KTM & Husaberg triple clamps; Fits ALL 1 1/8 over-sized handlebar mounts with 39-41mm spacing; Made in the USA.
Bushwackers Hand Guards by Giant Loop
$37.05
Heading into bad weather? Combine Bushwackers with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Protect hands - keep control; Cold & wet weather comfort; Brush, mud and trail protection; Strap on-off in seconds; Multiple mounting configurations to fit most motorcycle makes & models equipped with rigid hand guards and or deflectors; Tough stretch polyurethane strap (can be used separately); Custom wind foil shapes; No stitching or pieces to fail; When not using Bushwackers, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!; Made in USA.
Classic Enduro Replacement Handshields by Cycra
$19.95
Designed with Comfort Edge for extra coverage and unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with the Probend Handguards; Fits most other alloy handguards; Includes all hardware needed for mounting; Available in black, orange, blue, white; Made in the U.S.A.
Cycra Alloy Probend Handguard Pack with Hand Shields
$74.95
Bar Pack Includes: Probend Bars w/bumpers and Enduro Shields; For use with Fastco Handguard Hitch or BRP handguard mounts; Powergrip bar ends & hardware (mount clamps not included); CNC machined 6061 billet aluminum Probend Bars; Trademark Probend shape; Large area to accommodate hands and levers; High quality injection molded enduro style handshields; Integrated composite bumper to protect Probend Bars; Plus a new and improved bar end mount.
The Cycra Probend CRM (Center Reach Mount) "Factory Edition" Handguard System is designed to allow superior clearance for cable and hoses on a wide range of handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Powergrip alloy bar ends fit standard and oversized bars. Black anodized alloy Center Reach handguards with plastic abrasion guards; Full "Factory" Graphic hand shields; Anodized black bars & mounts; Matching Probend guards; Front mount spacers; Black anodized Center Reach Mounting Clamps; Alloy bar end mounts; ALL mounting hardware.
Cycra Probend CRM Handguard Racer Pack 1 1/8
$119.95
The new Cycra Probend CRM (Center Reach Mount) Handguard System is designed to allow superior clearance for cable and hoses on a wide range of handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Powergrip alloy bar ends fit standard and oversized bars. Cycra CRM Probend Complete Racer Pack includes: Alloy Center Reach handguards with plastic abrasion guards; Center Reach Mounting Clamps; Plastic handshields; Alloy bar end mounts; ALL mounting hardware.
Cycra Probend CRM Handguard Racer Pack for Flexx Handlebars
$85.95
The New Cycra Probend Flexx Bar Handguard System is designed to work in conjunction with the shock absorbing benefits of the Fasst Flexx Handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Probend Racer Pack includes: Alloy handguards with plastic abrasion guards; Plastic handshields; Alloy bar ends; ALL mounting hardware for Flexx handlebars.
Dual Compound Kevlar Grips by Renthal
$19.95
The most advanced grip available. Renthal has developed a special reinforced grip made with increased wear resistance. The grip has all the properties you would expect from a Renthal grip but with the life extending properties of KEVLAR brand resin. KEVLAR reinforced grip; The base material is reinforced with millions of randomly aligned KEVLAR fibers. As the grip is used, more Kevlar fibers are exposed; This KEVLAR layer offers three times the life of the regular compound which allows us to use a very supple matrix material; This revolutionary material lasts three times as long as our regular soft material; For use with twist throttles; If you use glue on the installation of Renthal grips, due to the specific compound, only Renthal grip glue will work.
Flexx Handlebars
Anti-Vibration Inserts by Fasstco
$59.95
A Discreet yet incredibly effective component to any serious racer or casual rider, Fasstco anti-vibration inserts do a great job of absorbing vibration transferred from the bars to your hand, yielding less fatigue and arm pump. Riderss have been installing them in anything with handlebars, from quads to superbikes, with great results. Constructed out of brass with an elastomer expansion joint mounted inside of the handlebars. The Anti-Vibration Bar Insert Kit comes with different end caps to accommodate most handguard systems plus end-caps for use without handguards. Quick and easy install; CNC machined from bras; Incredibly effective; Less hand fatigue and arm pump; Used by factory teams; Fits most aluminum handlebars; Great for dirt, dual-sport, street, road-racing; Made in the U.S.A.
Billet Throttle Tube for KTM, Husaberg, Gas Gas by G2 Ergo
$59.95
The G2 Throttle Tube consists of the ultra-smooth G2 tube with Delrin inserts fitted with a 100 throttle cam that is the same size as stock. The throttle tube shares the unique G2 cam and tube interlock that allows the rider to update to a quicker turn or control cam, sold separately, at any time. Burley replacement for wimpy plastic/nylon tubes; Includes throttle tube with stock size cam; Machined from 6061 aluminum; Self-lubricating Delrin bushings at each end of tube provide an ultra-smooth feel; Included cam is removable and can be replaced with alternate cams (sold separately) to fine tune control; Fits inside the stock throttle housing to stock cables; Removable end cap for simple handguard installation; Installs in minutes; Made in the U.S.A.
Bushwackers Hand Guards by Giant Loop
$37.05
Heading into bad weather? Combine Bushwackers with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Protect hands - keep control; Cold & wet weather comfort; Brush, mud and trail protection; Strap on-off in seconds; Multiple mounting configurations to fit most motorcycle makes & models equipped with rigid hand guards and or deflectors; Tough stretch polyurethane strap (can be used separately); Custom wind foil shapes; No stitching or pieces to fail; When not using Bushwackers, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!; Made in USA.
Classic Enduro Replacement Handshields by Cycra
$19.95
Designed with Comfort Edge for extra coverage and unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with the Probend Handguards; Fits most other alloy handguards; Includes all hardware needed for mounting; Available in black, orange, blue, white; Made in the U.S.A.
Cycra Alloy Probend Handguard Pack with Hand Shields
$74.95
Bar Pack Includes: Probend Bars w/bumpers and Enduro Shields; For use with Fastco Handguard Hitch or BRP handguard mounts; Powergrip bar ends & hardware (mount clamps not included); CNC machined 6061 billet aluminum Probend Bars; Trademark Probend shape; Large area to accommodate hands and levers; High quality injection molded enduro style handshields; Integrated composite bumper to protect Probend Bars; Plus a new and improved bar end mount.
Cycra Probend CRM Handguard Racer Pack for Flexx Handlebars
$85.95
The New Cycra Probend Flexx Bar Handguard System is designed to work in conjunction with the shock absorbing benefits of the Fasst Flexx Handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Probend Racer Pack includes: Alloy handguards with plastic abrasion guards; Plastic handshields; Alloy bar ends; ALL mounting hardware for Flexx handlebars.
Dual Compound Kevlar Grips by Renthal
$19.95
The most advanced grip available. Renthal has developed a special reinforced grip made with increased wear resistance. The grip has all the properties you would expect from a Renthal grip but with the life extending properties of KEVLAR brand resin. KEVLAR reinforced grip; The base material is reinforced with millions of randomly aligned KEVLAR fibers. As the grip is used, more Kevlar fibers are exposed; This KEVLAR layer offers three times the life of the regular compound which allows us to use a very supple matrix material; This revolutionary material lasts three times as long as our regular soft material; For use with twist throttles; If you use glue on the installation of Renthal grips, due to the specific compound, only Renthal grip glue will work.
Enduro DX Replacement Shields by Cycra
$25.95
Unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with all Probend Handguards; Sleek plastic shield with rubber edge; Fits many other alloy handguard brands; Includes all mounting hardware; Available in black, orange, blue, white; Made in the U.S.A.
Enduro Engineering Handlebar Risers for KTM, Husaberg, Husqvarna
$39.50
The Enduro Engineering bar riser kit lets you simply and quickly raise your handlebars from 5-30mm depending on the interlocking 6061 aluminum CNC machined pieces you choose. Kit includes: 2 each 5mm, 10mm,15mm riser blocks; Mounting bolts.
Fasst Flexx Handlebars
$359.95
No other handlebar on the market can provide the rider with the performance and comfort benefits that the patented Fasst Flexx Handlebar system can. The Fasst Flexx Handlebar system provides the most comfortable ride possible and virtually eliminates vibration and reduces joint pain, arm pump, and hand fatigue. From a beginning trail rider to a pro motocrosser, across the board performance and comfort will be gained with the Fasst Flexx Handlebar system. The handlebar flexes in the same plane as the front suspension allowing a natural movement for your arms that compliments the suspension. The rider can also control how soft or stiff the Fasst Flexx Handlebar system rides as well as adjusting the rise of the handlebar. These options can be obtained through changing the elastomers and shims to create the perfect bend and desired stiffness for your needs.
Flexx Accessories
Anti-Vibration Inserts by Fasstco
$59.95
A Discreet yet incredibly effective component to any serious racer or casual rider, Fasstco anti-vibration inserts do a great job of absorbing vibration transferred from the bars to your hand, yielding less fatigue and arm pump. Riderss have been installing them in anything with handlebars, from quads to superbikes, with great results. Constructed out of brass with an elastomer expansion joint mounted inside of the handlebars. The Anti-Vibration Bar Insert Kit comes with different end caps to accommodate most handguard systems plus end-caps for use without handguards. Quick and easy install; CNC machined from bras; Incredibly effective; Less hand fatigue and arm pump; Used by factory teams; Fits most aluminum handlebars; Great for dirt, dual-sport, street, road-racing; Made in the U.S.A.
Billet Throttle Tube for KTM, Husaberg, Gas Gas by G2 Ergo
$59.95
The G2 Throttle Tube consists of the ultra-smooth G2 tube with Delrin inserts fitted with a 100 throttle cam that is the same size as stock. The throttle tube shares the unique G2 cam and tube interlock that allows the rider to update to a quicker turn or control cam, sold separately, at any time. Burley replacement for wimpy plastic/nylon tubes; Includes throttle tube with stock size cam; Machined from 6061 aluminum; Self-lubricating Delrin bushings at each end of tube provide an ultra-smooth feel; Included cam is removable and can be replaced with alternate cams (sold separately) to fine tune control; Fits inside the stock throttle housing to stock cables; Removable end cap for simple handguard installation; Installs in minutes; Made in the U.S.A.
Bushwackers Hand Guards by Giant Loop
$37.05
Heading into bad weather? Combine Bushwackers with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Protect hands - keep control; Cold & wet weather comfort; Brush, mud and trail protection; Strap on-off in seconds; Multiple mounting configurations to fit most motorcycle makes & models equipped with rigid hand guards and or deflectors; Tough stretch polyurethane strap (can be used separately); Custom wind foil shapes; No stitching or pieces to fail; When not using Bushwackers, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!; Made in USA.
Classic Enduro Replacement Handshields by Cycra
$19.95
Designed with Comfort Edge for extra coverage and unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with the Probend Handguards; Fits most other alloy handguards; Includes all hardware needed for mounting; Available in black, orange, blue, white; Made in the U.S.A.
Cycra Alloy Probend Handguard Pack with Hand Shields
$74.95
Bar Pack Includes: Probend Bars w/bumpers and Enduro Shields; For use with Fastco Handguard Hitch or BRP handguard mounts; Powergrip bar ends & hardware (mount clamps not included); CNC machined 6061 billet aluminum Probend Bars; Trademark Probend shape; Large area to accommodate hands and levers; High quality injection molded enduro style handshields; Integrated composite bumper to protect Probend Bars; Plus a new and improved bar end mount.
Cycra Probend CRM Handguard Racer Pack for Flexx Handlebars
$85.95
The New Cycra Probend Flexx Bar Handguard System is designed to work in conjunction with the shock absorbing benefits of the Fasst Flexx Handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Probend Racer Pack includes: Alloy handguards with plastic abrasion guards; Plastic handshields; Alloy bar ends; ALL mounting hardware for Flexx handlebars.
Dual Compound Kevlar Grips by Renthal
$19.95
The most advanced grip available. Renthal has developed a special reinforced grip made with increased wear resistance. The grip has all the properties you would expect from a Renthal grip but with the life extending properties of KEVLAR brand resin. KEVLAR reinforced grip; The base material is reinforced with millions of randomly aligned KEVLAR fibers. As the grip is used, more Kevlar fibers are exposed; This KEVLAR layer offers three times the life of the regular compound which allows us to use a very supple matrix material; This revolutionary material lasts three times as long as our regular soft material; For use with twist throttles; If you use glue on the installation of Renthal grips, due to the specific compound, only Renthal grip glue will work.
Enduro DX Replacement Shields by Cycra
$25.95
Unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with all Probend Handguards; Sleek plastic shield with rubber edge; Fits many other alloy handguard brands; Includes all mounting hardware; Available in black, orange, blue, white; Made in the U.S.A.
Enduro Engineering Handlebar Risers for KTM, Husaberg, Husqvarna
$39.50
The Enduro Engineering bar riser kit lets you simply and quickly raise your handlebars from 5-30mm depending on the interlocking 6061 aluminum CNC machined pieces you choose. Kit includes: 2 each 5mm, 10mm,15mm riser blocks; Mounting bolts.
Fasstco Handguard Hitch Handguard Mounting System by BRP
$69.95
The new BRP Flexx Handguard Hitch hand guard mounts use a 10mm bolt that threads directly into the steel pivot pin on the Fasst Flexx Bars. This new and improved design is stronger and more durable than the previous design which utilized an 8mm bolt. The BRP M10 Flexx Mounts allow easy mounting to Cycra Probend hand guards and most other popular aluminum hand guard brands. The BRP Flexx mounts are designed to retain the movement of the Fasst Flexx handlebar's flexion system. Manufactured from billet 6061 T-6 aluminum; High quality fit and finish; Black anodized with laser etched BRP logo; Retains full movement of the elastomer pivot system; Quick and easy installation.
Handlebar Accessories
Anti-Vibration Inserts by Fasstco
$59.95
A Discreet yet incredibly effective component to any serious racer or casual rider, Fasstco anti-vibration inserts do a great job of absorbing vibration transferred from the bars to your hand, yielding less fatigue and arm pump. Riderss have been installing them in anything with handlebars, from quads to superbikes, with great results. Constructed out of brass with an elastomer expansion joint mounted inside of the handlebars. The Anti-Vibration Bar Insert Kit comes with different end caps to accommodate most handguard systems plus end-caps for use without handguards. Quick and easy install; CNC machined from bras; Incredibly effective; Less hand fatigue and arm pump; Used by factory teams; Fits most aluminum handlebars; Great for dirt, dual-sport, street, road-racing; Made in the U.S.A.
Billet Throttle Tube for KTM, Husaberg, Gas Gas by G2 Ergo
$59.95
The G2 Throttle Tube consists of the ultra-smooth G2 tube with Delrin inserts fitted with a 100 throttle cam that is the same size as stock. The throttle tube shares the unique G2 cam and tube interlock that allows the rider to update to a quicker turn or control cam, sold separately, at any time. Burley replacement for wimpy plastic/nylon tubes; Includes throttle tube with stock size cam; Machined from 6061 aluminum; Self-lubricating Delrin bushings at each end of tube provide an ultra-smooth feel; Included cam is removable and can be replaced with alternate cams (sold separately) to fine tune control; Fits inside the stock throttle housing to stock cables; Removable end cap for simple handguard installation; Installs in minutes; Made in the U.S.A.
BRP Hand Guard Mounts
$69.95
BRP Hand Guard Mounts are a perfect hand guard mounting solution when space is limited or when controls interfere with standard hand guard mounts. Also a great option for Scotts sub mounted damper applications applications. Made from aircraft quality aluminum and black anodized for a trick look. BRP Hand Guard Mounts have the same contour and shape as BRP & Scotts SUB Mounts. Fits all 39 41mm spacing over-sized 1 1/8 handle bar mounts. KTM, Husabergs, etc.) Kit includes all necessary hardware: Perfect solution when space is limited or controls/cables/hoses interfere; CNC machined from strong aircraft quality aluminum billet; Black anodized; Same shape and contour as BRP & Scott triple clamps; Works well with Scotts Sub mount damper kits; Fits stock KTM & Husaberg triple clamps; Fits ALL 1 1/8 over-sized handlebar mounts with 39-41mm spacing; Made in the USA.
Bushwackers Hand Guards by Giant Loop
$37.05
Heading into bad weather? Combine Bushwackers with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Protect hands - keep control; Cold & wet weather comfort; Brush, mud and trail protection; Strap on-off in seconds; Multiple mounting configurations to fit most motorcycle makes & models equipped with rigid hand guards and or deflectors; Tough stretch polyurethane strap (can be used separately); Custom wind foil shapes; No stitching or pieces to fail; When not using Bushwackers, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others! Made in USA.
Classic Enduro Replacement Handshields by Cycra
$19.95
Designed with Comfort Edge for extra coverage and unparalleled freedom of movement; Constructed of high-impact, injection-molded plastic; Designed to work with the Probend Handguards; Fits most other alloy handguards; Includes all hardware needed for mounting; Available in black, orange, blue, white; Made in the U.S.A.
Cycra Alloy Probend Handguard Pack with Hand Shields
$74.95
Bar Pack Includes: Probend Bars w/bumpers and Enduro Shields; For use with Fastco Handguard Hitch or BRP handguard mounts; Powergrip bar ends & hardware (mount clamps not included); CNC machined 6061 billet aluminum Probend Bars; Trademark Probend shape; Large area to accommodate hands and levers; High quality injection molded enduro style handshields; Integrated composite bumper to protect Probend Bars; Plus a new and improved bar end mount.
The Cycra Probend CRM (Center Reach Mount) "Factory Edition" Handguard System is designed to allow superior clearance for cable and hoses on a wide range of handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Powergrip alloy bar ends fit standard and oversized bars. Black anodized alloy Center Reach handguards with plastic abrasion guards; Full "Factory" Graphic hand shields; Anodized black bars & mounts; Matching Probend guards; Front mount spacers; Black anodized Center Reach Mounting Clamps; Alloy bar end mounts; ALL mounting hardware.
Cycra Probend CRM Handguard Racer Pack 1 1/8
$119.95
The new Cycra Probend CRM (Center Reach Mount) Handguard System is designed to allow superior clearance for cable and hoses on a wide range of handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Powergrip alloy bar ends fit standard and oversized bars. Cycra CRM Probend Complete Racer Pack includes: Alloy Center Reach handguards with plastic abrasion guards; Center Reach Mounting Clamps; Plastic handshields; Alloy bar end mounts; ALL mounting hardware.
Cycra Probend CRM Handguard Racer Pack for Flexx Handlebars
$85.95
The New Cycra Probend Flexx Bar Handguard System is designed to work in conjunction with the shock absorbing benefits of the Fasst Flexx Handlebars. Cycra's patented manufacturing process uses the highest quality 6061 Aluminum for maximum strength and a secure precise fit. Probend Racer Pack includes: Alloy handguards with plastic abrasion guards; Plastic handshields; Alloy bar ends; ALL mounting hardware for Flexx handlebars.
Dual Compound Kevlar Grips by Renthal
$19.95
The most advanced grip available. Renthal has developed a special reinforced grip made with increased wear resistance. The grip has all the properties you would expect from a Renthal grip but with the life extending properties of KEVLAR brand resin. KEVLAR reinforced grip; The base material is reinforced with millions of randomly aligned KEVLAR fibers. As the grip is used, more Kevlar fibers are exposed; This KEVLAR layer offers three times the life of the regular compound which allows us to use a very supple matrix material; This revolutionary material lasts three times as long as our regular soft material; For use with twist throttles; If you use glue on the installation of Renthal grips, due to the specific compound, only Renthal grip glue will work.
Services
Slavens Racing offers a variety of services including suspension re-valves, suspension re-builds, engine modifications and engine re-builds for KTM 2 strokes, KTM & Husaberg 4 strokes, and KTM Dual Sport, Super Enduro and Adventure.
Standard re-valve is NOT AVAILABLE for closed chamber bladder forks ('07 SX '08 - '13 XC, SX) The WP open chamber fork has very stiff high speed compression valving and incorrect spring rates for many riders. This creates harsh and deflective (bouncing off the chosen line) action when riding on the rocks, roots, and square edged bumps, insufficient bottoming resistance on the big hits, vague steering and tracking, head shake, and overall instability. After reviewing your service order form and consulting with you, the internal damping circuits will be re-designed, spring rates will be changed, and oil levels adjusted to match your weight, skill level, age, riding style, (sitting vs standing) and type of terrain encountered. When matched with a Slavens shock re-valve, your bike will have precise steering, will be more comfortable, confidence inspiring, safer, and will track straight in all conditions. 'Re-valve includes: Valving shims; Cartridge fork fluid; Clean and inspect all parts; Labor; 60 day warranty; Unlimited phone support; Re-work if needed. Does not include springs, seals, bushings, or other worn/damaged parts. 3 - 4 day turnaround time with an appointment. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
The Next Level Fork Re-Valve
$499.00
The Next Level is for those that want the best. Because of time and expense constraints this service has only been offered to a few customers in the past, but now CNC water jet machining technology makes this affordable to the masses. The Next Level Re-Valve, with its Slavens designed High Flow Passive Valve Pistons, makes the fork action much more compliant and responsive when riding on rocks and roots yet increases firmness for G-outs and big hits. (Add $70 to the re-valve price to include SKF oil seals) The Next Level Re-Valve includes everything that is in the Standard Fork Re-Valve plus: Next Level High Flow Passive Valve Pistons Additional hand machining to valving parts Does not include springs, seals, bushings, or other worn/damaged parts.. 3 - 4 day turnaround time with an appointment. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
The Next Level Fork Re-valve and Pressure Balance System (PBS)
Besides the usual harshness, deflection, and spring rate issues, the WP closed chamber bladder fork has a pressure build-up issue that is very labor intensive to correct. This service is HIGHLY RECOMMENDED for ALL applications, especially when competing in events that require non-stop riding for 2-3 hour periods. Under these conditions increased stiffness and deflection will be experienced from pressure build-up in the inner cartridge and outer chamber and in extreme cases and conditions the fork becomes rigid and un-rideable. Manual bleeding of the air from the outer chamber does not cure the problem. This service is only available at Slavens Racing. Developed by Jeff Slavens and Kelvin Thomas. This service includes everything that is in the Standard Re-Valve plus: Next Level High Flow Passive Valve Pistons; Proprietary cartridge, stanchion tube, and HL ring machining to reduce pressure balance issues; SKF fork seals (rebuild included); Vacuum bleed cartridge with WP/KTM vacuum bleeding machine. Does not include springs, bushings, or other worn/damaged parts. 3 4 day turnaround time with an appointment. Shock Sox or Seal Savers recommended for all models, applications, and conditions.
Our rebuilds go far beyond what you get at most dealerships or suspension shops where they just throw in a set of seals. A correct rebuild involves a very thorough cleaning of all internals (the shim stacks, valving pistons and other parts are often full of sludge), inspection, and repair/replacement of all internal wear items. (bushings, rebound check valve shims, o-rings, stuck rebound needles, etc.) Closed cartridge forks are vacuum bled with our WP/KTM vacuum bleeding machine. Re-build price includes: SKF Oil Seals; Disassemble; Clean, inspect, repair, service all internals; Polish fork tubes & damper rods; Labor; Replace worn parts; Re-assemble w/quality cartridge fluid; Vacuum bleed cartridge with WP/KTM vacuum bleeding machine; Update valving if previously re-valved by Slavens Racing (valving parts not included); 60 day warranty (Shock Sox or Seal Savers must be installed). Does not include bushings or other worn/damaged parts. 3 - 4 day turnaround time with an appointment. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
The WP shock suffers from harsh high speed compression valving, insufficient rebound valving and soft spring rates. This creates poor straight line stability and cornering, kicking, low ride height, and insufficient bottoming resistance. The spring rate needs to be adjusted for most riders and the internal valving settings should be corrected. After reviewing your service order form and consulting with you, the internal damping circuits will be re-designed and spring rates will be changed to match your weight, skill level, age, riding style, (sitting vs standing) and type of terrain encountered. Note: Progressive rate shock springs are used for all off-road applications (with PDS linkless system) and ALL shocks are bled with a WP Factory vacuum/pressure bleeding machine. (Add $35 - $60 to the re-valve price to include oil seals). Standard Re-valve includes: Valving parts; Nitrogen; Shock fluid; labor; Bleed fluid with WP Factory vacuum/pressure bleeding machine; 60 day warranty; Re-work if needed; Unlimited phone support. Does not include springs, seals, or bushings. 3 - 4 day turnaround time with an appointment.
ALL PDS MODELS '98-'13$299.00
Next Level Shock Re-valve
The Next Level shock re-valve gives additional plushness and increased bottoming resistance. Overall it has a firmer feel than our standard re-valve but is actually more responsive and more plush on the small trail trash, rocks, and roots yet has considerably more bottoming resistance and rebound control that absorbs whoops and G-outs. This is accomplished by installing our proprietary anti-bottoming needle (PDS models) and modifications to the valving pistons and Compression Control (DCC) adjuster. Note: '11 & '12 linkage models suffer from insufficient low-speed compression valving. This allows the rear suspension to compress too much (squat) and creates vague steering. Our Next Level valving corrects this and improves steering precision and overall stability. We do not recommend aftermarket linkage. (Add $35 - $60 to the re-valve price to include oil seals). Next Level shock re-valve includes everything that comes with the standard re-valve plus: KT needle for increased bottoming resistance; Valving piston mods for increased plushness; Dual Compression Control (DCC) mods for increased plushness; Hand made rebound shims for improved response (PDS). Does not include springs, seals, or bushings. 3 - 4 day turnaround time with an appointment.
ALL PDS models '06-'12 & all linkage models '11-'13$439.00
Shock Re-Build
$225.00
– $275.00
WP PDS shocks are the most complicated brand to rebuild correctly. Most shops overlook many wear areas that effect maximum performance and they leave the shock fluid full of air by attempting to bleed the system without proper equipment. This makes the damping performance inconsistent and quick to fade. At Slavens Racing ALL shocks are bled with a WP/KTM vacuum/pressure bleeding machine to insure correct and consistent performance.Rebuild includes: Disassemble; Shaft oil seal or sealhead assembly (sealhead,bushing, oil & dust seal); Shock fluid; Nitrogen; Clean & inspect all parts; Replace other worn parts (parts not included)Re-assemble & re-charge with nitrogen; Bleed fluid with WP/KTM vacuum/pressure bleeding machine. 3 - 4 day turnaround time with an appointment.
Fork or Shock Height/Travel Reduction
Please call or email info@slavensracing.com for pricing. Many of today's motorcycles are tall for the average rider and can be overwhelming for riders with inseams of 30 inches or less. Reducing the ride height 1 to 2 inches makes it much easier to navigate technical sections, reduces low speed tip-overs, and greatly increases rider confidence. The travel reduction modification involves the installation of travel limiting spacers, (so that the fork or shock shaft extends to a reduced position) installing shorter fork springs (except '07 SX,SXF and '08-'13 SX, SXF, XC), and re-valving to match the reduced travel and your riding conditions. The travel reduction can be reversed back to full travel for approximately half of the original cost. Travel reduction is recommended for trail riding, enduros and motard. It is NOT offered or recommended for motocross or high speed desert applications.
Notice: This service is discontinued. This mod gives a major increase to the bottom-end and mid-range torque with added top-end over-rev, all of which make it easier to climb hills/mountains and allows you to use taller gearing. 1st gear will be more usable and 6th gear will be better for cruising to the next trail head. The power delivery is smoother than stock and enables you to put the power to the ground on slick surfaces and makes it less tiring to ride all day long. Fuel mileage is improved and pump gas works well. Like all of our Mule Porting, this is not a minor change. It's a major boost to the entire power-band that makes it much easier and more fun to ride and more competitive against larger displacement engines. Major increase to low-end and mid-range torque and horsepower with increased top-end over-rev; Smooth power delivery; Increased torque makes it easier to ride; Pulls a taller gear in most situations (climb hills in 3rd that you used to climb in 2nd); Increases traction; Makes it easier to re-jet; Increases fuel mileage; Does NOT decrease engine life; Runs on pump fuel; 3 - 4 day turnaround time with an appointment; Does NOT include servicing, cleaning, or re-assembly of powervalves.
KTM 200 EXC/XC/XC-W '04 - '12$499.00
Slavens Mule Port & Polish
Notice: This service is discontinued. Most years of the KTM 250 have mid-range power-band engines with weak bottom-end power, a decent mid-range, and a lack luster top end with a likeable quick reving, light, and zippy feel. The Slavens Mule Port & Polish gives a major boost from bottom to top yet retains the likeable stock traits. The much needed boost to the low-end and mid-range torque will make it pull much harder off corners and up hills, will require less clutch action and added top-end hit and over-rev will come in handy on long straights when you want to blast by a friend or competitor. This mod must be combined with a SX head. Major increase to low-end and mid-range torque and horsepower with good top-end power; Smooth power delivery; Increased torque makes it easier to ride; Pulls a taller gear in most situations (climb hills in 3rd that you used to climb in 2nd); Increases traction; Makes it easier to re-jet; Increases fuel mileage; Does NOT decrease engine life; Runs on pump fuel; 3 - 4 day turnaround time with an appointment; Does NOT include servicing, cleaning, or re-assembly of powervalves.
KTM 250EXC/MXC/XC/SX/XC-W '04 - '12$499.00
Slavens Mule Port/Polish/Decking/Head Mod
Notice: This service is discontinued. The Mule Port & Polish/Cylinder Decking/Head Mod combination offers a significant boost to the low-end and mid-range torque and horsepower. It's NOT a minor change that you can barely notice, it's a major boost. The increased torque and horsepower produces smooth power delivery which makes it much easier to ride, increases traction, and enables using a taller gear in most situations. These mods, when combined with a Slavens Mountain Jet Kit, increase fuel mileage. All cylinder decking and head mods will have the compression ratio adjusted to work in the elevation range in which they will be ridden. (example: engines to be used at low elevation will have a lower compression ratio than engines designed for mountain use only). Major increase to low-end and mid-range torque and horsepower with good top-end power; Smooth power delivery; Increased torque makes it easier to ride; Pulls a taller gear in most situations (climb hills in 3rd that you used to climb in 2nd); Increases traction; Makes it easier to re-jet; Increases fuel mileage; Does NOT decrease engine life; Runs on pump fuel; 3 - 4 day turnaround time with an appointment; Does NOT include servicing, cleaning, or re-assembly of powervalves.
KTM 300EXC/MXC/XC/XC-W '04 -'10$629.00
KTM 300XC/XC-W '11-'12$589.00
Head Mod - Available
Very noticeable and usable boost to the low-end and mid-range power that will make your 300 easier to ride. This mod can be used with a stock or ported cylinder. This is a very inexpensive bang for the buck.... a no brainer. Works well with pump gas, race gas is not needed or recommended; Does not require re-jetting; Helps clean up jetting issues; Does not adversely affect top-end performance; Machining/compression ratio is adjusted to match your elevation; Compatible with all types of riding & racing; Does not increase coolant or engine temperature; Does not include new head o-rings or jetting specs; 2 day turnaround time - no appointment, email, or phone call necessary; Please include a completed service form with the shipment. KTM 250 head mod - We do not offer a 250 EXC, XC, XC-W head mod because the 250 SX head (available here 250 SX head) is far superior to machining the stock head.
KTM 300EXC/MXC/XC/XC-W '04 -'14$55.00
Cylinder Decking (machining the base gasket surface) - Available
This mod, when combined with the head mod, is the biggest bang for the buck on '04-'11 models. It gives a big boost to the low-end and mid-range torque. If you are watching your budget, I highly recommend the cylinder decking combined with the head mod. Pump gas works well, race gas is NOT needed. Turnaround time is 2 days. No need for an appointment, email, or phone call. Just include a completed service form and ship it.
KTM 300EXC/MXC/XC/XC-W '04 - '11$65.00
Powervalve Service
Notice: This service is discontinued. Dis-assemble; De-carbon, clean, polish; Assemble & lubricate; Set timing; Set "Z" dimension (flap height) (250&300); Install new o-rings; Seal front cover plate; Parts are NOT included.
The WP open chamber fork has very stiff high speed compression valving and incorrect spring rates for many riders. This creates harsh and deflective (bouncing off the chosen line) action when riding on the rocks, roots, and square edged bumps, insufficient bottoming resistance on the big hits, vague steering and tracking, head shake, and overall instability. After reviewing your service order form and consulting with you, the internal damping circuits will be re-designed, spring rates may be changed, and oil levels adjusted to match your weight, skill level, age, riding style, (sitting vs standing) and type of terrain encountered. When matched with a Slavens shock re-valve, your bike will have precise steering, will be more comfortable, confidence inspiring, safer, and will track straight in all conditions. (Add $70 to the re-valve price to include oil seals & labor to change the seals. Only high quality SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) Re-valve includes: Valving shims; Cartridge fork fluid; Clean and inspect all parts; Labor; 60 day warranty; Unlimited phone support; Re-work if needed. Does not include springs, seals, bushings, or other worn/damaged parts. Shock Sox are recommended for all models, applications, and conditions. On '08 - '13 models the fork guard guide ring must be removed for correct fitment.
The Next Level Fork Re-Valve
$499.00
ALL models with open chamber fork. Highly recommended for all 2007 - 2013 models. The Next Level is for those that want the best. Because of time and expense constraints this service has only been offered to a few customers in the past, but now CNC water jet machining technology makes this affordable to the masses. The Next Level Re-Valve, with its Slavens designed High Flow Passive Valve Pistons, makes the fork action much more compliant and responsive when riding on rocks and roots yet increases firmness for G-outs and big hits. (Add $70 to the re-valve price to include oil seals & labor to change the seals. Only high quality SKF forks seals are used. The Next Level Re-Valve includes everything that is in the Standard Fork Re-Valve plus: Next Level High Flow Passive Valve Pistons; Additional hand machining to valving parts. Does not include springs, seals, bushings, or other worn/damaged parts. Shock Sox are recommended for all models, applications, and conditions. On '08 - '12 models the fork guard guide ring must be removed for correct clearance.
The Next Level Fork Re-valve and Pressure Balance System (PBS)
$629.00
All models with closed chamber bladder fork only. Besides the usual harshness, deflection, and spring rate issues, the WP closed chamber bladder fork has a pressure build-up issue that is very labor intensive to correct. This service is HIGHLY RECOMMENDED for ALL applications, especially when competing in events that require non-stop riding for 2-3 hour periods. Under these conditions increased stiffness and deflection will be experienced from pressure build-up in the inner cartridge and outer chamber and in extreme cases and conditions the fork becomes rigid and un-rideable. Manual bleeding of the air from the outer chamber does NOT cure the problem. This service is only available at Slavens Racing. Developed by Jeff Slavens and Kelvin Thomas and race tested by Team KTM/RPM WORCS rider Kyle Summers. This service includes everything that is in the Standard Re-Valve plus: Next Level High Flow Passive Valve Pistons; Proprietary cartridge, stanchion tube, and HL ring machining to reduce; pressure balance issues; SKF triple lip fork seals (rebuild included); Vaccuum bleed cartridge with WP/KTM vaccuum bleeding machine. Does not include springs, bushings, or other worn/damaged parts. Shock Sox recommended for all models, applications, and conditions. On '08 - '12 models the fork guard guide ring must be removed for correct fitment.
Fork Seal Change & Re-build
Our rebuilds go far beyond what you get at most dealerships or suspension shops where they just throw in a set of seals. A correct rebuild involves a very thorough cleaning of all internals (the shim stacks, valving pistons and other parts are often full of sludge), inspection, and repair/replacement of all internal wear items. (bushings, rebound check valve shims, o-rings, stuck rebound needles, etc.) Closed cartridge forks are vacuum bled with our WP/KTM vacuum bleeding machine. Re-build price includes: SKF oil & dust seals; Disassemble; Clean, inspect, repair, service all internals; Polish fork tubes & damper rods; Labor; Replace worn parts; Re-assemble w/quality cartridge fluid; Vacuum bleed cartridge with WP/KTM vacuum bleeding machine (closed chamber forks only); Update valving if previously re-valved by Slavens Racing (valving parts not included); 60 day warranty (Shock Sox must be installed). Does not include bushings, or other worn/damaged parts. Shock Sox are recommended for all models, applications, and conditions. On '08 - '12 models the fork guard guide ring must be removed for correct fitment.
All PDS MODELS '98-'13, All linkage models '11 - '13, All Husaberg '09 -'13. The WP shock suffers from harsh high speed compression valving, insufficient rebound valving and soft spring rates. This creates poor straight line stability and cornering, kicking, low ride height, and insufficient bottoming resistance. The spring rate needs to be adjusted for most riders and the internal valving settings should be corrected. After reviewing your service order form and consulting with you, the internal damping circuits will be re-designed and spring rates will be changed to match your weight, skill level, age, riding style, (sitting vs standing) and type of terrain encountered. Note: Progressive rate shock springs are used for all off-road applications with PDS linkless system (straight rate springs are used for linkage models) and ALL shocks are bled with a WP Factory vacuum/pressure bleeding machine. NOTE: The '11-'13 linkage models squat too much in the rear and this compromises overall balance and steering precision. This is quite easily resolved in our standard and next level valving. (Add $29 - $60 to the re-valve price to include oil seals & labor to change the seals.) Standard Re-valve includes: Valving parts; Nitrogen; Shock fluid; Labor; Bleed fluid with WP/KTM Factory vacuum/pressure bleeding machine; 60 day warranty; Re-work if needed; Unlimited phone support. Does not include springs, seals, or bushings.
Next Level Shock Re-valve
The Next Level shock re-valve gives additional plushness and increased bottoming resistance. Overall it has a firmer feel than our standard re-valve but is actually more responsive and more plush on the small trail trash, rocks, and roots yet has considerably more bottoming resistance and rebound control that absorbs whoops and G-outs. This is accomplished by installing our proprietary anti-bottoming needle and modifications to the valving pistons and Dual Compression Control (DCC) adjuster. Next Level shock re-valve includes everything that comes with the standard re-valve plus: KT needle for increased bottoming resistance; Valving piston mods for increased plushness; Dual Compression Control (DCC) mods for increased plushness; Hand made rebound shims for improved response. Does not include springs, seals, or bushings.
All KTM PDS models '06-'09, All Husaberg '09$439.00
All '10-'13 KTM & Husaberg PDS models$419.00
Shock Re-Build
$225.00
– $275.00
WP PDS shocks are the most complicated brand to rebuild correctly. Most shops overlook many wear areas that effect maximum performance and they leave the shock fluid full of air by attempting to bleed the system without proper equipment. This makes the damping performance inconsistent and quick to fade. At Slavens Racing ALL shocks are bled with a WP/KTM vacuum/pressure bleeding machine to insure correct and consistent performance. Rebuild includes: Disassemble; Shaft oil seal or sealhead assembly (sealhead,bushing, oil & dust seal); Shock fluid; Nitrogen; Clean & inspect all parts; Replace other worn parts (parts not included); Re-assemble & re-charge with nitrogen; Bleed fluid with WP/KTM vacuum/pressure bleeding machine.
Fork or Shock Height/Travel Reduction
Please call or email info@slavensracing.com for pricing. Many KTMs and Husabergs are tall for the average rider and can be overwhelming for riders with inseams of 30 inches or less. Reducing the ride height 1 to 2 inches makes it much easier to navigate technical sections, reduces low speed tip-overs, and greatly increases rider confidence. The travel reduction modification involves the installation of travel limiting spacers, (so that the fork or shock shaft extends to a reduced position) installing shorter fork springs (except '07 SX,SXF and '08-'13 SX, SXF, XC), and re-valving to match the reduced travel, your weight, skill level, and your riding conditions. The travel reduction can be reversed back to full travel for approximately half of the original cost. Travel reduction is recommended for trail riding, enduros and motard. It is NOT offered or recommended for motocross or high speed desert applications.
KTM Dual Sport, Super Enduro & Adventure Services
KTM 640 Adventure '03-'07
Standard Fork Re-Valve
$349.00
$239 + Springs ($110) = $349.(Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The 640 Adventure WP fork is harsh on the small hits (rocks, roots, washboard, etc.) and very mushy on medium to big hits. This combination of harshness and softness creates vague steering and tracking, head shake, and overall instability. For ALL riders over 150lbs, this bike desperately needs firmer spring rates and matching valving. The harshness and wiggly wobbly handling will be a thing of the past. Your confidence and enjoyment will skyrocket and you'll feel like Cyril Depres at the Dakar Rally. Re-valve includes: Valving shims, Cartridge fork fluid, Clean and inspect all parts, Labor, 60 day warranty, Unlimited phone or email support, Re-work if needed. Does not include seals, bushings, or other worn/damaged parts. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
The Next Level Fork Re-Valve
$449.00
$339 + springs ($110) = $449. (Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The Next Level is for those that want the best. Because of time and expense constraints this service has only been offered to a few customers in the past, but now CNC water jet machining technology makes this affordable to the masses. The Next Level Re-Valve, with its Slavens designed High Flow Passive Valve Pistons, makes the fork action much more compliant and responsive when riding on rocks and roots yet increases firmness for G-outs and big hits. The Next Level Re-Valve includes everything that is in the Standard Fork Re-Valve plus: Next Level High Flow Passive Valve Pistons, Additional hand machining to valving parts. Does not include seals, bushings, or other worn/damaged parts. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
Shock Re-Valve
$349.00
$239 + Spring ($110) = $349 (Add $29 for an oil seal kit). The 640 Adventure WP shock suffers from a soft spring, wallowy low-speed compression valving, and a rebound circuit that is unable to control a firmer spring rate. Once these issues are corrected, the shock will be able to handle a wide variety of terrain and loads. It's highly recommend that this be paired with the fork re-valve/re-spring to achieve proper balance and handling performance both on and off road. Re-valve includes: Valving parts, Nitrogen, Shock fluid, Labor, Bleed fluid with WP/KTM Factory vacuum/pressure bleeding machine, 60 day warranty, Re-work if needed, Unlimited phone or email support. Does not include seals or bushings.
KTM 690E & R Enduro '08-'11
Next Level Fork Re-Valve
$339.00
(We don't recommend the standard revalve for the 690 because of the extremely harsh fork and chassis combination) Add $60 to the re-valve price to include oil seals & labor to change the seals. (Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare). The 690E & R WP fork is brutally harsh and stiff on the small hits (rocks, roots, washboard, etc.). This creates a very nervous front end and makes it a handful to ride in any conditions that are rougher than fresh pavement. For many riders a spring rate change is necessary. Re-valve includes: Valving shims, Cartridge fork fluid, Next Level High Flow Passive Valve Pistons, Hand machining to valving parts, Clean and inspect all parts, Labor, 60 day warranty, Unlimited phone or email support, Re-work if needed. Does not include springs, seals, bushings, or other worn/damaged parts. Shock Sox or Seal Savers are recommended for all models, applications, and conditions.
Shock Re-Valve
$239.00
The 690E & R WP shock suffers from the same problems as the front-end, extremely harsh valving that makes it kick and track poorly. Once these issues are corrected, the shock will be able to handle a wide variety of terrain and loads. It's recommend that this be paired with the fork re-valve/re-spring to achieve proper balance and handling performance both on and off road. Standard Re-valve includes: Valving parts, Nitrogen, Shock fluid, Labor, Bleed fluid with WP/KTM Factory vacuum/pressure bleeding machine, 60 day warranty, Re-work if needed, Unlimited phone or email support. Does not include springs, seals, or bushings.
KTM 950 Super Enduro '07-'09
Standard Fork Re-Valve
$239.00
(Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The 950 Super Enduro WP fork is brutally harsh and stiff on the small hits (rocks, roots, washboard, etc.) which makes it very nervous at the speeds that this beast can deliver. When custom tuned to your weight and riding conditions it will be very stable and comfortable. Re-valve includes: Valving shims, Cartridge fork fluid, Clean and inspect all parts, Labor, 60 day warranty, Unlimited phone or email support, Re-work if needed. Does not include springs, seals, or bushings.
The Next Level Fork Re-Valve
$339.00
(Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The Next Level is for those that want the best. Because of time and expense constraints this service has only been offered to a few customers in the past, but now CNC water jet machining technology makes this affordable to the masses. The Next Level Re-Valve, with its Slavens designed High Flow Passive Valve Pistons, makes the fork action much more compliant and responsive when riding on rocks and roots yet increases firmness for G-outs and big hits. The Next Level Re-Valve includes everything that is in the Standard Fork Re-Valve plus: Next Level High Flow Passive Valve Pistons, Additional hand machining to valving parts. Does not include springs, seals, or bushings.
Shock Re-Valve
$239.00
The 950 Super Enduro WP shock suffers from the same problems as the front-end, extremely harsh valving that makes it kick and track poorly. Once these issues are corrected, the shock will be able to handle a wide variety of terrain and loads. It's recommend that this be paired with the fork re-valve to achieve proper balance and handling performance both on and off road. Re-valve includes: Valving parts, Nitrogen, Shock fluid, Labor, Bleed fluid with WP/KTM Factory vacuum/pressure bleeding machine, 60 day warranty, Re-work if needed, Unlimited phone or email support. Does not include springs, seals, or bushings.
KTM 950/990 Adventure '03-'11
Standard Fork Re-Valve
$349.00
$239 + Springs ($110) = $349. (Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The 950/990 Adventure WP fork is harsh on the small hits (rocks, roots, washboard, etc.), soft on big hits, and dives too much during braking. This combination of harshness and softness creates vague steering and tracking, drifting when the throttle is adjusted or chopped in a turn, and overall instability, especially on washboard gravel roads. For most riders it needs a firmer spring rate to correct the balance issues and a re-valve to correct the harshness. Re-valve includes: Valving shims, Cartridge fork fluid, Clean and inspect all parts, Labor, 60 day warranty, Unlimited phone or email support, Re-work if needed. Does not include seals, or bushings.
The Next Level Fork Re-Valve
$449.00
(Add $60 to the re-valve price to include oil seals & labor to change the seals. Only high quality NOK or SKF forks seals are used. We've tested all of the cheaper brands and they don't compare.) The Next Level is for those that want the best. Because of time and expense constraints this service has only been offered to a few customers in the past, but now CNC water jet machining technology makes this affordable to the masses. The Next Level Re-Valve, with its Slavens designed High Flow Passive Valve Pistons, makes the fork action much more compliant and responsive when riding on rocks and roots yet increases firmness for G-outs and big hits. The Next Level Re-Valve includes everything that is in the Standard Fork Re-Valve plus: Next Level High Flow Passive Valve Pistons, Additional hand machining to valving parts. Does not include seals or bushings.
Shock Re-Valve
$239.00
The 950/990 Adventure WP shock suffers from stiff high-speed compression valving, that causes the rear end to dance around during acceleration on choppy gravel roads and soft low-speed compression valving that allows the bike to wallow, especially in curves with dips. For some years/models and for some riders, the spring rate may need to be adjusted for correct balance and support. Re-valve includes: Valving parts, Nitrogen, Shock fluid, Labor, Bleed fluid with WP/KTM Factory vacuum/pressure bleeding machine, 60 day warranty, Re-work if needed, Unlimited phone or email support. Does not include springs, seals, or bushings.
Fork Seal Change & Re-build
Our rebuilds go far beyond what you get at most dealerships or suspension shops where they just throw in a set of seals. A correct rebuild involves a very thorough cleaning of all internals (the shim stacks, valving pistons and other parts are often full of sludge), inspection, and repair/replacement of all internal wear items. (bushings, rebound check valve shims, o-rings, stuck rebound needles, etc.) Re-build price includes: NOK or SKF Oil Seals (we've tested many other brands and they don't compare); Disassemble; Clean, inspect, repair, service all internals; Polish fork tubes & damper rods; Labor; Replace worn parts; Re-assemble w/quality cartridge fluid; Update valving if previously re-valved by Slavens Racing (valving parts not included). 60 day warranty (Shock Sox or Seal Savers must be installed) Does not include bushings or other worn/damaged parts. Shock Sox or Seal Savers are recommended for all models, applications and conditions.
All models 625,640,690,950,990$200.00
Shock Re-Build
WP shocks are the most complicated brand to rebuild correctly. Most shops overlook many wear areas that effect maximum performance and they leave the shock fluid full of air by attempting to bleed the system without proper equipment. This makes the damping performance inconsistent and quick to fade. At Slavens Racing ALL shocks are bled with a WP/KTM vacuum/pressure bleeding machine to insure correct and consistent performance. Rebuild includes: Disassemble; Shaft oil seal or sealhead assembly (sealhead,bushing, oil & dust seal); Shock fluid; Nitrogen; Clean & inspect all parts; Replace other worn parts (parts not included); Re-assemble & re-charge with nitrogen; Bleed fluid with WP/KTM vacuum/pressure bleeding machine.
All models 625,640,690,950,990$180.00–$220.00
Fork or Shock Height/Travel Reduction
Many KTMs seat height can be overwhelming for riders with inseams of 30 inches or less. Reducing the ride height 1 to 2 inches makes it much easier to navigate technical sections, reduces low speed tip-overs, and greatly increases rider confidence. The travel reduction modification involves the installation of travel limiting spacers, (so that the fork or shock shaft extends to a reduced position) installing shorter fork springs (shocks often don't require shorter springs because most have preload adjusters that can compensate for the shorter travel) and re-valving to match the reduced travel, your weight, skill level, and your riding conditions. The travel reduction can be reversed back to full travel for approximately half of the original cost. Travel reduction is recommended for trail riding, enduros, dual sport, adventure and motard.
About
Jeff Slavens is a 39 year veteran of the motorcycle industry
having worked as a line mechanic, factory mechanic, dealership owner/operator and current owner of Jeff Slavens Racing.
In the 70s he and his two brothers raced Maicos.
It was kind of a Team Maico Slavens, but as Randy Hawkins once stated, too many stallions in the same barn is not always a good thing. Every race day their mother was worried sick because when the gate dropped (back then it was actually a rubber band) the brotherly love was gone and the race was ON and they thought nothing of taking out the other in the pursuit of the win.
Those early Maico days are where Jeff's engine and suspension skills began to develop.
Maico Break-O was not allowed if you wanted to beat your brother so there were endless hours devoted to repairs, rebuilds, tuning, and suspension mods. He and his brothers studied magazine pictures of the factory Maico team bikes and cut, bent, and welded their frames to accommodate a lay-down shock position and increase wheel travel. From there shock and fork mods were developed by Team Slavens because there were no off the shelf items available.
His first affiliation with factory race teams was in the 80s with the then dominate Team Husqvarna.
Later in the 80s and 90s it was with Team KTM and Team Suzuki and from then until now with Randy Hawkins Team Am Pro Yamaha.
When he worked for the Husky team he ported cylinders and did head mods for the entire team (enduro, HS, desert, mx).
Boxes with dozens of cylinders (for the many National Champions and up and comers like Randy Hawkins) would arrive several times per year and of course they always needed them yesterday.
Also during the 80s he started a long working relationship with then new comer Rodney Smith, who rode MX for Team Yamaha at the time.
They first met just a few minutes before the first moto of a Washougal, Washington National MX. Jeff was there tuning for top ten Yamaha rider, Mark Flesia, when Rodney rode up and asked for help. His YZ125 was a dog, so Jeff took it for a little test spin in the jetting area. He returned and told Rodney to run up to the start line and pick a starting position while he rode the bike over to Rodneys pit and started barking out orders to Rodneys dad whom he had never met. They tore the carb apart in record time, changed some brass and Jeff blasted up to the starting line where engines were running. Rodney hopped on the bike, pulled the holeshot, and they've been friends every since. Rodney went on to win 5 Brazilian national Championships, placed 3rd in the World 250 MXGP, 3 National HS Championships, 5 National Reliability Championships, 6 ISDE Gold Medals (top American twice), and 5 GNCC Championships.
In the 80s Husqvarna was the dominant team in all types of off-road racing and Jeff was the cylinder and head guy for the entire team.
Cagiva bought Husqvarna in the late 80s and ran it in the ground so the team riders were all looking for work . Many of them switched to Suzuki so then Jeff became the engine guy for that team. At approximately the same time Team KTM asked for some help and Jeff built the 290cc engine that Kevin Hines used to win the National Enduro Championship.
And then came the Javelin, Randy Hawkins.
Jeff had built engines for the new young punk from South Carolina while he was with Team Husqvarna but the funny talking kid came on strong when he got comfortable on his Slavens ported, Dale Stegal tuned RMX and later on YZs. Randy went on to win 73 Nationals, 7 National Enduro Championships, and 12 ISDE Gold Medals with Slavens Mule Motors. He was recently inducted into the Motorcycle Hall of Fame.
Now at age 58 Jeff enjoys traveling the world with his wife Sue to see the sites.
architecture, learn about different cultures and find new friends and great places to eat. During the summer and fall you'll find him riding the Gnar on some of Colorado's gnarliest trails.
Jeff Slavens is a 39 year veteran of the motorcycle industry, having worked as a line mechanic, factory mechanic, dealership owner/operator and current owner of Jeff Slavens Racing.
In the 70?s he and his two brothers raced Maicos. It was kind of a Team Maico Slavens, but as Randy Hawkins once stated, too many stallions in the same barn is not always a good thing. Every race day their mother was worried sick because when the gate dropped (back then it was actually a rubber band) the brotherly love was gone and the race was ON and they thought nothing of taking out the other in the pursuit of the win.
Jeff Slavens Racing is proud to offer American made aftermarket products for KTM, Honda, Yamaha, Kawasaki, Suzuki, Husqvarna, Husaberg and GasGas.
Jeff Slavens Racing offers a variety of services including suspension re-valves and re-builds and engine modifications and re-builds for KTM and Husaberg.